DSC PK5500/RFK5500 Installation Instructions Manual Download Page 26

Page: 26 / 32

Wiring

1. Before wiring the unit, ensure

that all power (AC transformer

and battery) is disconnected

from the control panel.

2. Connect the four Keybus wires

from the control panel (red,

black, yellow and green) to the

keypad terminals. See diagram:

3. If programmed as an input, you can connect a device - such as a

door contact - to the P/Z terminal of the keypad. This eliminates the

need to run wires back to the control panel for the device. To connect

the zone, run one wire from the device to the P/Z terminal and the

other wire from the device to the B (black) terminal. For powered

devices, run the red wire to the R (positive) terminal and the black

wire to the B (negative) terminal. When using end of line supervi-

sion, connect the zone according to one of the configurations out-

lined in your system’s Installation Manual.

4. If the ‘P/Z’ terminal is programmed as an output, the output follows

the PGM programmed in Section [080]. A small relay, buzzer or

other DC operated device may be connected between the positive

supply voltage and the ‘P/Z’ terminal (maximum load is 50mA).

Applying Power

Once all wiring is complete, and the equipment is secured to the build-

ing structure with at least two screws apply power to the control panel:
1. Connect the battery leads to the battery.
2. Connect the AC transformer.
For more information on control panel power specifications, see the

control panel Installation Manual.

Programming the Keypad

There are several program-

ming options available for

the keypad. These are

described below. Program-

ming the keypad is similar

to programming the rest of

the system. When you are

in the keypad program-

ming sections, the keypad

will display which options

are turned on along the top

of the display. To turn an option on or off, press the number corre-

sponding to the option on the number pad. The numbers of the

options that are currently turned ON will be displayed. For example, if

options 1 and 4 are on, the display will look like this on the different

keypad displays:

For information on programming the rest of your security system,

please refer to your system’s Installation Manual.

Broadcasting LCD Labels

All LCD programming is done per keypad. If more than one LCD key-

pad is present on the system, labels programmed at one keypad can

be broadcast to all other LCD keypads. Perform the following procedure

in order to broadcast labels:
Step 1 - Program one LCD keypad completely.
Step 2 - Make sure all LCD keypads are connected to the Keybus.
Step 3 - Enter keypad programming by pressing [



][8][Installer

Code][



], then enter section [998] at the keypad that was pro-

grammed. The keypad will now broadcast all the information pro-

grammed to all the other LCD keypads on the system.
Step 4 - When the keypad is finished press the [#] key to exit.

NOTE: LCD Label broadcast from this keypad is only compatible with

PC1616/1832/1864 control panels and other PK5500/RFK5500 key-

pads.

Language Programming

(PK5500\RFK5500 Only)

Hold (<>) keys for 2 seconds to enter language programming,

scroll to the desired language and Press [



] to select.

NOTE: If section [077] option 4 is OFF, language programming

can only be performed while in installers programming.

Enrolling the Keypad

The keypad will need to be assigned to a partition and slot if supervi-

sion or keypad zones are being used. Keypad assignments and key-

pad option programming must be done at each keypad individually.

The 1st digit of keypad assignment is used to determine partition

assignment (1 to 8). If partitioning is not used, enter [1]. For Global

Keypads, enter [0].

NOTE: LED and ICON keypads cannot be programmed as Global Keypads.

The 2nd digit of keypad assignment is used to determine slot assign-

ment for keypad supervision. Each keypad will be assigned a different

slot number from 1 to 8. PK5500 and RFK5500 LCD keypads come

defaulted in slot 8. If LCD keypads are used one LCD keypad must

remain in slot 8.

NOTE: The RFK55XX enrolls as two modules:
Light 1 = keypad section of the RFK55XX
Light 17 = receiver section of the RFK55XX
NOTE: Deleting all wireless devices from the RFK55XX or defaulting the

RFK55XX will cause a supervisory fault.

Enter the following at each keypad installed on the system:

1. Enter Installer Programming by pressing [



][8][Installer’s Code].

2. Press [000] for Keypad Programming.

3. Press [0] for Partition and Slot Assignment.

4. Enter the 1st digit (0 to 8 for partition assignment).

5. Enter the 2nd digit (1 to 8 for slot assignment supervision).

6. Press the [#] key twice to exit programming.

7. After assigning all keypads, perform a supervisory reset by entering

[