18
To arm the partition which you are at simply press [
✱
✱
✱
✱
✱
] or
use the hotkey (0). The message
EXIT DELAY
IN PROGRESS
will appear on the keypad with the exit delay timer if it is
enabled. Instead of arming their own partition, if the user
decides to select another partition to arm the message
SELECT (0)
< >
ARM PARTITION
R
Use the arrow keys to scroll to the “For Options” menu.
Selecting (0) “To Arm” will arm the selected partition and
display the message
EXIT DELAY
IN PROGRESS
for 2 seconds and then return the user to the arming
menu of their own partition.
If (1) “For Options” is selected the user will be prompted
with the message
KEYPAD LOANED TO
(Partition Label)
From here the user is capable of performing all [
✱
✱
✱
✱
✱
]
functions (e.g. [
✱
✱
✱
✱
✱
] [7] Door Strike) and arm the panel
using conventional methods.
Once the [#] key is pressed or 20 seconds of idle time
(no key presses made or not active in a submenu) the
keypad will return to its normal state displaying the
message
RETURNING TO
(Partition Label)
Disarming
Enter the premises through the designated exit-entry
door. The keypad buzzer will be on. Go to the keypad
and enter the 4 digit or 6 digit access code. If an error is
made in entering the code, press the [#] key and enter
the code again. The “Armed” light will go out and the
keypad buzzer will stop. The correct access code must
be entered before the allowed entry time expires. To
change the entry time see “Installers Programming
Command”, [
✱
✱
✱
✱
✱
][8]. If an alarm occurred while the panel
was armed, the “View Memory” message will be on the
display with the zone name for the zone that caused the
alarm. The display will keep those messages on for two
minutes or until the [#] key is pressed to return the panel
to the normal arm-disarm mode.
To disarm by using a multi partition access code the
keypad will display the message
(0) TO ARM
< >
(Partition Label)
R
The lower right hand corner of the display will show the
partition status using the letter “R” for Ready, and “N” for
Not ready.
Use the [<] [>] keys to scroll though the assigned
partitions. Only partitions to which the access code is
assigned will be displayed. The message
(2) TO SELECT
< >
(Partition Label)
A
will be displayed with the partition status at the right corner
of the LCD.
To disarm the partition being viewed simply press [
✱
] or
use the hot key (0). If (1)“For Options” is selected the user
will be prompted with the message
KEYPAD LOANED TO
(Partition Label)
on the LCD display. From here the user is capable of
performing all
✱
functions (e.g. [
✱
] [7] Door Strike) and arm
the panel using the conventional methods.
Once the [#] key is pressed or 20 seconds of idling time (no
key presses made or not active in a submenu) the keypad
will return to its normal state displaying the message
RETURNING TO
(Partition Label)
Auto-bypass/Home-Away Arming
If a correct access code is entered and you do not exit the
premises, the system will, at the end of the Exit delay time,
arm with interior zones automatically bypassed if those
interior zones have been programmed as “Home-Away”
zones. These zones will remain bypassed until [
✱
✱
✱
✱
✱
][1] is
entered to reactivate bypassed home-away zones.
This is a convenience feature for the user who wishes to
remain on the premises with the system armed. The user
does not have to manually bypass the Home-Away zones.
To reactivate the Home-away zones that have been
automatically bypassed, press [
✱
✱
✱
✱
✱
][1]. This command is a
quick method of fully arming the system in residential
applications before going to bed.
Note: The auto-bypassed zones will only send a tamper
alarm when the tamper condition is activated, using
Double EOL resistors.
Zone Bypassing
[
✱
]+[1]
A bypassed zone will not cause an alarm. If a zone is
bypassed the panel may be armed even if the zone is open.
Use zone bypassing when access is needed to part of the
protected area. Also, damaged wiring or contacts on a
zone may be temporarily bypassed until repairs can be
made so that the panel can be armed.
To bypass zones, enter [
✱
✱
✱
✱
✱
] [1]. An access code may be
required if the installer has enabled that option. A menu will
appear.
[0] Bypass Open Zones
[0] Bypass Open Zones
[0] Bypass Open Zones
[0] Bypass Open Zones
[0] Bypass Open Zones allows the user to bypass only the
open zones that are on that partition. Use the [<][>] keys to
scroll through the open zones. Next to the zone label will
the a [!] this character is used to indicate that the zone is
open. To select the open zone to be bypassed press the
[
✱
✱
✱
✱
✱
] key. A [
✱
✱
✱
✱
✱
] will appear next to the zone label to indicate
that the zone has been bypassed.
Summary of Contents for maxsys PC4020KT
Page 15: ...11 Module Hookup Diagram ...
Page 35: ......
