DryAIR 2250 Operator'S Manual Download Page 6

Safety Concerns

2-2

Material Safety Data Sheet

BOSS  CHILL  PG

MSDS

Canadian  Centre  for  Occupational  Health  and  Safety

Issue:    2001-4  (November,  2001)

***MATERIAL  SAFETY  DATA***

1 .

CHEMICAL  PRODUCT  &  COMPANY  IDENTIFICATION

PRODUCT  NAME: .................................... PROPYLENE GLYCOL INDUSTRIAL
PRODUCT  CODE: ...................................... 70511
EFFECTIVE DATE: .................................... 05/23/03

DATE PRINTED 10/09/03

MSD:  000248

COMPANY  IDENTIFICATION: ............... The Dow Chemical Company, Midland, MI 48674
EMERGENCY  TELEPHONE  NUMBER: . 24-HOUR EMERGENCY PHONE NUMBER  989-636-4400

...................................................................... Customer Information Center:  800-258-2436

2 .

COMPOSITION/INFORMATION  ON  INGREDIENTS

Propylene  glycol

CAS#  000057-55-6

99%

3 .

HAZARDS  IDENTIFICATION

EMERGENCY OVERVIEW: ....................... Colorless, odorless liquid.  Toxic fumes released in fire situations.

POTENTIAL  HEALTH  EFFECTS: ................. (See  Section  11  for  toxicological  data.)
EYE: ...................................................................... May  cause  slight  transient  (temporary)  eye  irritation.    Corneal  injury  is  unlikely.    Mists  may

cause  eye  irritation.

SKIN: .................................................................... Prolonged  contact  is  essentially  nonirritating  to  skin.   A  single  prolonged  skin  exposure  is  not

likely  to  result  in  the  material  being  absorbed  through  skin  in  harmful  amounts.    Repeated
exposures  may  cause  flaking  and  softening  of  skin.    May  be  absorbed  in  potentially  harmful
amounts  when  applied  in  large  quantities  to  severe  burns  (second  or  third  degree)  over  large
areas  of  the  body  as  part  of  a  cream  or  other  topical  application.   Absorption  under  such
circumstances  can  elevate  serum  osmolality  and  may  result  in  osmotic  shock.

INGESTION: ........................................................ Single  dose  oral  toxicity  is  considered  to  be  extremely  low.    No  hazards  anticipated  from

swallowing  small  amounts  incidental  to  normal  handling  operations.

INHALATION: .................................................... At  room  temperature,  vapors  are  minimal  due  physical  properties.  Mists  may  cause  irritation

of  upper  respiratory  tract.

SYSTEMATIC: .................................................... (OTHER  TARGET  ORGAN)  EFFECTS:    Repeated  excessive  ingestion  may  cause  central

nervous  system  effects.

CANCER  INFORMATION: ............................... Did  not  cause  cancer  in  long-term  animal  studies.
TERATOLOGY  (BIRTH  DEFECTS): .............. Birth  defects  are  unlikely.    Exposures  having  no  adverse  effects  on  the  mother  should  have

no  effect  on  the  fetus.

REPRODUCTIVE  EFFECTS: ............................ In  animal  studies,  has  been  shown  not  to  interfere  with  reproduction.

4 .

FIRST AID

EYE: ...................................................................... Flush  eyes  with  plenty  of  water.
SKIN: .................................................................... Wash  off  in  flowing  water  or  shower.
INGESTION: ........................................................ No  adverse  effects  anticipated  by  this  route  of  exposure  incidental  to  proper  industrial

handling.

INHALATION: .................................................... Remove  to  fresh  air  if  effects  occur.    Consult  a  physician
NOTE  TO  PHYSICIAN: .................................... No  specific  antidote.    Supportive  care.    Treatment  based  on  judgment  of  the  physician  in

response  to  reactions  of  the  patient.

5 .

FIRE FIGHTING MEASURES

FLASH  POINT: .................... 218

°

F,  103

°

C

METHOD  USED: ................ PMCC
FLAMMABLE  LIMITS ...... LFT:  2.6%
LFL:      2.6%
UFL:  12.5%
HAZARDOUS  COMBUSTION  PRODUCTS:    During  a  fire,  smoke  may  contain  the  original  material  in  addition  to  unidentified  toxic

and/or  irritating  compounds.    Hazardous  combustion  products  may  include  and  are  not  limited  to:  aldehydes,  carbon  monoxide.

OTHER  FLAMMABILITY  INFORMATION:    Violent  steam  generation  or  eruption  may  occur  upon  application  of  direct  water  stream

to  hot  liquids.    Spills  of  these  organic  liquids  on  hot  fibrous  insulations  may  lead  to  lowering  of  the  autoignition  temperatures
possibly  resulting  in  spontaneous  combustion.

EXTINGUISHING  MEDIA:    Water  fog  or  fine  spray,  carbon  dioxide,  dry  chemical,  foam.    Alcohol  resistant  foams  (ATC  type)  are

preferred  if  available.    General  purpose  synthetic  foams  (including  AFFF)  or  protein  foams  may  function,  but  much  less  effectively.
Do  not  use  direct  water  stream.    Will  spread  fire.

MEDIA  TO  BE AVOIDED:    Do  not  use  direct  water  stream.
FIRE  FIGHTING  INSTRUCTIONS:    Keep  people  away.    Isolate  fire  area  and  deny  unnecessary  entry.    Burning  liquids  may  be  moved  by

flushing  with  water  to  protect  personnel  and  minimize  property  damage.    Burning  liquids  may  be  extinguished  by  dilution  with  water.
Do  not  use  direct  water  stream.    May  spread  fire.

PROTECTIVE  EQUIPMENT  FOR  FIRE  FIGHTERS:    Wear  positive-pressure,  self-contained  breathing  apparatus  (SCBA)  and  protective

fire-fighting  clothing  (including  fire-fighting  helmet,  coat,  pants,  boots,  and  gloves).    If  protective  equipment  is  not  available  or  not
used,  fight  fire  from  a  protected  location  or  safe  distance.

Summary of Contents for 2250




















Reviews: