background image

 
 

18 

 

 

 

 

A comparison table is provided between the classification of NLGI lubricants (National Lubricating Grease Institute) and the 
ASTM classification (American Society for Testing and Materials) for greases for the values that concern the pump. 
 

GREASES 

NLGI 

ASTM 

000 

445 – 475 

00 

400 – 430 

355 – 385 

310 – 340 

265 – 295 

 

For further information about the technical specifications and the safety measures to adopt, refer to the product safety sheet 
(Directive 93/112/EEC) relative to the type of lubricant selected and supplied by the manufacturer. 

 
 
 

15. 

CLEANING

 

 

It is necessary to remove periodically dust from pump avoiding the spread in the air. For this operation refers to Safety Officer. 
 
 
 

16. 

TRAINING

 

 

Personnel assigned to installation, electrical connections and ordinary and special maintenance of the pump, must have at least 
8  hours  of  specific  training  by  an  appropriate  organism  on  equipment  for  explosive  atmospheres  caused  by  the  inflammable 
gases and combustible dusts. 
 

 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 

NOTE: 

The pump was designed to operate with lubricants with a maximum rating NLGI 2. Use lubricants that are compatible with 
NBR gaskets. Any internal residual lubricant used for assembly and testing purposes is NLGI 2 oil

 

 

 

Summary of Contents for Mini-SUMO






















Reviews: