Drolet Escape 1400-I Insert Owner'S Manual Download Page 27

27 

DROLET LIMITED LIFETIME WARRANTY 

 
The    warranty  of  the  manufacturer  extends  only  to  the  original  consumer  purchaser  and  is  not  transferable.  This  warranty 
covers brand new products only,  which have not been altered, modified nor repaired since shipment from factory. Proof of 
purchase  (dated  bill  of  sale),  model  name  and  serial  number  must  be  supplied  when  making  any  warranty  claim  to  your 
DROLET dealer.   

This warranty applies to normal residential use only. Damages caused by misuse, abuse, improper installation, lack of 
maintenance,  over  firing,  negligence  or  accident  during  transportation,  power  failures,  downdrafts,  or  venting 
problems are not covered by this warranty. 

This warranty does not cover any scratch, corrosion, distortion, or discoloration. Any defect or damage caused by the use of 
unauthorized  parts  or  others  than  original  parts  void  this  warranty.  An  authorized  qualified  technician  must  perform  the 
installation  in  accordance  with  the  instructions  supplied  with  this  product  and  all  local  and  national  building  codes.  Any 
service call related to an improper installation is not covered by this warranty. 

The  manufacturer  may require that defective products be returned or that digital pictures be provided to support the claim. 
Returned products are to be shipped prepaid to the manufacturer for investigation. If a product is found to be defective, the 
manufacturer will repair or replace such defect. Transportation fees to ship the product back to the purchaser will be paid by 
the  manufacturer.  Repair  work  covered  by  the  warranty,  executed  at  the  purchaser’s  domicile  by  an  authorized  qualified 
technician requires the prior approval of the manufacturer. Labour cost and repair work to the account of the manufacturer 
are  based  on  predetermined  rate  schedule  and  must  not  exceed  the  wholesale  price  of  the  replacement  part.  All  parts  and 
labour costs covered by this warranty are limited according to the table below.   

The  manufacturer at its discretion  may decide to repair or replace any part or unit after inspection and investigation of the 
defect. The manufacturer may, at its discretion, fully discharge all obligations with respect to this warranty by refunding the 
wholesale  price  of  any  warranted  but  defective  parts.  The  manufacturer  shall  in  no  event  be  responsible  for  any  special, 
indirect, consequential damages of any nature, which are in excess of the original purchase price of the product. A one-time 
replacement limit applies to all parts benefiting from a lifetime coverage. This warranty applies to products purchased after 
October 1

st

, 2011. 

 

DESCRIPTION 

WARRANTY APPLICATION 

PARTS 

LABOUR 

Combustion chamber (welds only) and castings. 

Lifetime 

3 years 

Stainless steel firebox components, secondary air tubes*, surrounds and heat 
shields, ash drawer, steel legs, pedestal, trims (aluminum extrusions), 
plating* (defective manufacture), and convector air-mate. 

5 years 

3 years 

Carbon steel firebox components, glass retainers, handle assembly, C-Cast 
baffle*, and vermiculite baffle*. 

3 years 

1 year 

Standard blowers, heat sensors, switches, rheostat, wiring, and other controls. 

2 years 

1 year 

Optional blowers, ceramic glass (thermal breakage only*), paint (peeling), 
gaskets, insulation, and ceramic fibre blankets. 

1 year 

n/a 

Firebrick 

n/a 

n/a 

*Pictures required 
 
Shall your unit or a components be defective, contact immediately your DROLET dealer. Prior to your call make sure you 
have the following information necessary to your warranty claim treatment: 
 

 

Your name, address and telephone number;  

 

Bill of sale and dealer’s name; 

 

Serial number and model name as indicated on the 
nameplate fixed to the back of your unit; 

 

Nature of the defect and any relevant information. 

 
Before  shipping  your  unit  or  defective  component  to  our  plant,  you  must  obtain  from  your  DROLET  dealer  an 
Authorization  Number.  Any  merchandise  shipped  to  our  plant  without  authorization  will  be  refused  automatically 
and returned to sender. 

 

Summary of Contents for Escape 1400-I Insert




























Reviews: