manualshive.com logo in svg

Drill Master 69230, Owner'S Manual, Page: 12 / 16

Share
Download
Drill Master 69230 Owner'S Manual Download Page 12

Page 12

For technical questions, please call 1-800-444-3353.

Item 69230 

        

SAFETY

OPERA

TION

MAINTENANCE

SETUP

Installing the Rip Fence 

 

 

1.  Pull open the hinges on each end of the Rip Fence and 

fit the Rip Fence slots on the Table Top rim.

2.  Close the hinges to lock the Rip Fence in place. 

 

 

 

 

 

 

 

Adjusting the Miter Gauge

1.  Place the Miter Gauge assembly on top of the Rip Fence. 

2.  Loosen the Miter Gauge Knob counterclockwise, 

then rotate the gauge to the desired setting. 

3.  Tighten the Miter Gauge Knob clockwise. 

 

 

 

 

 

 

Work Piece and Work Area Set Up

1.  Designate a work area that is clean and well-lit.  

The work area must not allow access by children 

or pets to prevent distraction and injury.

2.  Route the power cord along a safe route to reach 

the work area without creating a tripping hazard 

or exposing the power cord to possible damage.  

The power cord must reach the work area with 

enough extra length to allow for a drip loop.

3.  Make sure that the Base is on a steady level 

work surface so the water level of the tank can 

be accurately measured and maintained.

4.  There must not be objects, such as utility lines, 

nearby that will present a hazard while working.

5.  Keep workpieces pressed firmly against 

the Table and Fence while cutting.

6.  Mark cut lines using waterproof marker or crayon.

General Operating Instructions

1.  Install the Blade and Upper and Lower Blade Guards.

2.  Fill the Water Tank to the Maximum fill line marked on the inside of the tank.

CAUTION:

 Do not operate the 

Tile Saw with too little or too much 

water in the Water Tank. Keep the 

water level between the minimum 

and maximum level markings on 

the inside of the Water Tank.

Figure 9

Hinge

Table 

Top Rim

Rip Fence Slot

Figure 10

Miter Gauge Knob

Miter Gauge Assembly

Rip Fence

Figure 11

Maximum fill line

Minimum fill line

Summary of Contents for 69230

















Reviews:

No comments