background image

User Manual 

RANGE HOOD | COMPACTA

 76 

 

 

 

1. 

 

RECOMMENDATIONS AND SUGGESTIONS  

 

INSTALLATION

 

• The manufacturer is not liable for damage caused by improper or improper installation. 

•  Please  read  this  instruction  manual  before  installing  and  using  the  extractor.  It  is 
important to keep this manual in a safe place for future reference. 

• This extractor can be used in conduit mode (external smoke ducts) or recirculation mode 
(internal recycling). The choice of modes can be left to the customers' decision. 

• Only a qualified technician can perform the installation work. 

• Check that the mains voltage corresponds to the voltage indicated on the inner plate of 
the extractor 

• Do not connect the extractor to the flue pipes (boilers, chimneys, etc.) 

• If the extractor is used in conjunction with non-electric appliances (eg gas appliances), a 
sufficient ventilation system must be provided in place to avoid backflow of exhaust gases. 
The  kitchen  should  have  a  direct  opening  in  the  open  air  in  order  to  ensure  the  entry  of 
clean air. 

•  The  minimum  installation  distance  to  the  kitchen  worktop  should  be  650  mm.  If  the 
installation manual of the gas cooker specifies a greater distance than the suggested one, 
it must be taken into account. 

• The extractor must be installed on a plate with four anchor points. 

 

NOTICE:  Taking  into  account  the  weight  of  the  extractor,  it  is  recommended  that  two  or 
more persons are required to install or move. Otherwise, it may cause physical injury. 

USE: 

•  The  extractor  has  been  designed  for  domestic  use  only,  to  remove  fumes  from  the 
kitchen. 

• Never use the extractor for purposes other than those intended. 

• When the extractor is operating, it must not be exposed to high flames below. 

• Adjust the flame intensity by which it should be directed to the bottom of the pots, making 
sure that the flame does not come out over the edge of the pot. 

• When frying, the flame intensity must be continuously monitored: very hot oil may burst 
into flames. 

Summary of Contents for COMPACTA 76















Reviews: