11
230312 rev.1 2015-01-22
Drester Monza 10 & Silverstone 12
The QuickLift is designed for both lifting the wheel into the
machine and lowering the wheel back down on the floor. Users
who want to bounce the wheels back down on the floor should
close the plate before doing this. Bouncing heavy wheels on
the plate might deform it.
Before using the QuickLift, read these instructions carefully.
1. Installation
When the machine is installed (see chapter 6), the lift plate
must be correctly adjusted. This can’t be factory set, since most
shop floors are not level. Ignoring adjusting the lift will void the
warranty. Not adjusting the lift before use may cause damages
to the floor from the plate being dragged along the floor, or
damages to the lift from dropping wheels on it.
Unfold the lift plate by pulling the sprint on the bottom right
side. Adjust the opening angle of the plate by moving the
eccentric washer on the bottom left side up or down. The plate
should touch the floor, but should separate from the floor as
soon as the lift starts moving. If the eccentric washer doesn’t
have enough travel, it could be turned up-side-down or front-
to-back.
Tighten the bolts after a good position of the plate is found.
Re-inspect the position of the lift plate after some usage to
make sure it instantly separates from the floor during operation.
2. Operation
Pull the knob to the right of the lift plate and fold it out with
your hand. Do not release it until it has touched the floor. In
precipitated position, the knob will automatically spring back
and work as a stop for accidentally closing the plate in upward
position. Closing the plate requires pulling the knob at the
same time.
Place the wheel on the lift plate and activate the lift by turning
the knob on the front panel to the left. The lift is weight
sensitive, this means it will lift heavier wheels that are standing
more stable on the plate faster (approximately 2-3 seconds).
Smaller and lighter wheels will be lifted slower, in
approximately 4 seconds. If faster lifting time for smaller wheels
is desired, the wheel can be pushed against the lift plate by the
operator during the start of the lift cycle.
The lift plate can be left in its upper position
during washing,
and the wheel could then be lowered back on the ground using
the lift.
PLEASE NOTE:
When lift plate is folded out and ready
to use for lifting, wheels should not be taken out of
the machine by bouncing them on the lift plate. Heavy
wheels will deform the lift plate.
16.
TECHNICAL SPECIFICATIONS
Producer:
HEDSON TECHNOLOGIES AB
Hammarvägen 4
S-232 37 ARLÖV
SWEDEN
Machine model:
SILVERSTONE 12/ SILVERSTONE 12/
MONZA 10
MONZA 10
400Volt
230Volt
Electrical connection:
400V 3~ 16A
230V 3~ 32A
Pump motor:
5,5 kW
5,5 kW
Rotation motor:
0,18 kW
0,18 kW
Operating current:
13A
23 A
Fuses needed :
16A B-fuse
1)
63A
1)
or higher
Compressed air connection: Min 8 bar
(120psi)
Min 8 bar
(120psi)
max 12 bar
(174psi)
max 12 bar
(174psi)
Water volume:
310 l
(82 US-gallon)
310 l
(82 US-gallon)
Height of unit:
1500 mm
(59”)
1500 mm
(59”)
Width of unit, body only:
1090 mm
(43”)
1090 mm
(43”)
Width of unit with QuickLift: 1170 mm
(46”)
1170 mm
(46”)
i.e. actual space
i.e. actual space
needed!
needed!
Depth of unit:
1250 mm
(49”)
1250 mm
(49”)
Weight:
SILVERSTONE SILVERSTONE
240 kg
(530 lbs)
240 kg
(530 lbs)
without water
without water
or ShotMedium
or ShotMedium
MONZA
MONZA
230 kg
(510 lbs)
230 kg
(510 lbs)
without water
without water
or ShotMedium
or ShotMedium
Weight QuickLift:
26 kg
(60 lbs)
26 kg
(60 lbs)
Maximum wheel weight:
60 kg
60 kg
Maximum wheel size:
860 x 360 mm
860 x 360 mm
Minimum wheel size:
540 x 145 mm
540 x 145 mm
Sound pressure level:
78 dB(A)
78 dB(A)
measured at
measured at
a distance of
a distance of
1 meter
1 meter
Sound power level:
94 dB(A)
94 dB(A)
1)
Assumes that no other electrical equipment is connected to this
fuse.
