-3-
Safety Rules for Charging
a.
This manual contains instructions for
power adapter model 510.
Do not
substitute any other power adapter.
b.
Before using power adapter, read all
instructions and cautionary markings on
(1) power adapter, and (2) product using
battery.
c.
Charge only Dremel HSGP-01.
Other
types of cordless tools may burst causing
personal injury and damage.
d.
Charge tool in temperatures above +41
degrees F (5 degrees C) and below +104
degrees F (40 degrees C). Store tool in
locations where temperatures will not
exceed 113 degrees F (45 degrees C).
This is important to prevent serious
damage to the battery cells.
e.
Do not recharge tool in damp or wet
environment. Do not expose power
adapter to rain or snow.
Water entering
power adapter may result in electric
shock or fire.
f.
Battery leakage may occur under
extreme
usage
or
temperature
conditions. Avoid contact with skin and
eyes.
The battery liquid is caustic and
could cause chemical burns to tissues. If
liquid comes in contact with skin, wash
quickly with soap and water. If the liquid
contacts your eyes, flush them with water
for a minimum of 10 minutes and seek
medical attention.
g.
Keep power adapter and glue pen away
from
flammable
material
when
recharging the glue pen.
Carpeting and
other heat insulating surfaces block
proper air circulation, which may cause
overheating of the power adapter and
tool. If smoke or melting of the power
adapter or tool is observed, unplug the
power adapter immediately and do not
use the tool or power adapter. Contact
customer service immediately.
h.
Make sure cord is located so that it will
not be stepped on, tripped over, or
otherwise subjected to damage or
stress.
Damaged plug and cord may
result in electric shock or fire.
i.
Disconnect the power adapter by pulling
the plug rather than the cord. Do not
operate power adapter with damaged
cord or plug; have them replaced
immediately.
Damaged plug or cord may
result in electric shock or fire.
j.
Do not disassemble power adapter or
operate the power adapter if it has
received a sharp blow, been dropped or
otherwise damaged in anyway.
Incorrect
reassembly or damage may result in
electric shock or fire.
k.
Before each use, check the power
adapter, cable and plug. If damage is
detected, do not use the power adapter.
Never open the power adapter yourself,
take it to a Dremel Factory Service
Center, or qualified serviceman only
using original spare parts.
Incorrect
reassembly may result in electric shock or
fire.
l.
Unplug tool from power adapter when
battery in tool is fully charged.
Tool left
plugged into the power adapter over a
long period of time could lead to tool
damage and fire.
m. Unplug power adapter from outlet
before
storage,
attempting
any
maintenance
or
cleaning.
Such
preventive safety measures reduce the
risk of electric shock or fire.
Battery Care
a.
DO NOT PUT BATTERIES INTO FIRE OR
EXPOSE TO HIGH HEAT.
They may
explode.
b.
Battery leakage may occur under
extreme
usage
or
temperature
conditions. Avoid contact with skin and
eyes.
The battery liquid is caustic and
could cause chemical burn to tissues. If
liquid comes in contact with skin, wash
quickly with soap and water. If the liquid
contacts your eyes, flush them with water
for a minimum of 10 minutes and seek
medical attention.
Battery Disposal
D o n o t a t t e m p t t o
disassemble the tool
or remove any component projecting
from the tool.
Fire or injury may result.
P r i o r t o d i s p o s a l , p r o t e c t e x p o s e d
terminals with heavy insulating tape to
prevent shorting.
LITHIUM-ION BATTERIES
If equipped with a lithium-ion battery,
the battery must be collected, recycled
or disposed of in an environ mentally
sound manner.
1605A000E8.qxp_HSGP-01 6/25/20 11:13 AM Page 3
