Dremel 8260, Original Instructions Manual

Page: 22 / 228

GENERAL
7
A. Collet nut
B. Collet
C. Nose cap (EZ Twist integrated wrench*)
D. Shaft
E. Shaft lock Button
F. On/Off switch
G. Variable Speed Dial
H. Red Warning LED
I. Bluetooth LED
J. Speed Indicator
K. Fuel Gauge
L. Battery Pack
M. Battery Release Tabs
N. Hanger
O. Ventilation openings
P. Collet Wrench
Q. Charger
R. Green light
CHARGING AND BATTERIES
• This charger can be used
by children aged 8 and
above and by persons
who have physical,
sensory or mental
limitations or a lack of
experience or knowledge
if a person responsible
for their safety supervises
them or has instructed
them in the safe
operation of the charger
and they understand
the associated dangers
(otherwise there is a
danger of operating errors
and injuries)
•
Supervise children
(this
will ensure that children do
not play with the charger)
• Only use DREMEL charger GAL 12V-20
2607226399 or 2607226401 (UK) or 2607226403
(AUS) and DREMEL battery pack 1607A350KW
with this tool
• Do not expose tool/charger/battery to rain
• Do not charge battery in damp or wet environments
• Do not use charger when damaged; take it to
one of the officially registered DREMEL Service
Stations for a safety check
• Do not use charger when cord or plug is damaged;
cord or plug should be replaced immediately at
one of the officially registered DREMEL Service
Stations
• Do not use battery when damaged; it should be
replaced immediately
• Do not disassemble charger or battery
• Do not attempt to recharge non-rechargeable
batteries with the charger
• Permitted ambient temperatures (tool/charger/
battery):
– when charging 0...+45ºC
– during operation -20...+50ºC
– during storage -20...+50ºC
CHARGING BATTERY PACK
1. Plug charger cord into your standard power outlet.
With no battery pack inserted, the charger’s green
indicator light will go ON. This indicates the charger
is receiving power and the charger is ready for
operation.
2. To remove the battery pack from the tool press
both battery release tabs and pull the battery from
the tool.
3. When you insert the battery pack into the charger,
the charger’s green indicator light will begin to
“BLINK”. This indicates that the battery is receiving
a fast charge.
4. When the indicator light stops “BLINKING” (and
becomes a steady green light) fast charging is
complete. The battery pack is fully charged and
can be removed from the charger. The light will
stop blinking in less time if the battery pack was
not completely discharged.
5. When you begin the charging process of the
battery pack, a steady green light could also
mean the battery pack is too hot or too cold. Fast
charging is only possible when the temperature
range of the battery pack is between 0°C and
45°C. As soon as the battery pack reaches the
correct temperature range, the battery charger will
automatically switch to fast charging.
6. The battery pack may be used even though
the light may still be blinking. The light may
require more time to stop blinking depending on
temperature.
7. A substantial drop in operating time per charge
may mean that the battery pack is nearing the end
of its life and should be replaced.
8. Remember to unplug charger during storage
period.
ACCESSORIES
ALWAYS TURN OFF THE TOOL BEFORE
CHANGING ACCESSORIES
Use only Dremel tested accessories. Be sure to
read the instructions supplied with your Dremel
accessory for further information on its use.
Handle and store accessories carefully to avoid
chipping and cracking.
CHANGING ACCESSORIES
9
A. Collet nut
B. Collet (3.2 mm)
C. Nose cap (EZ Twist integrated wrench*)
D. Dremel chuck 4486*
E. Shaft lock button
F. Wrench
*) not standard included
22 23