Draytek Vigor3300V+ User Manual Download

Page: 170 / 230

Vig Series User’s Guide

162

For Default Configuration

Click

Default

tab. The following page of default configuration will be shown:

Profile Status

Set the initialization of IPSec Tunnel with this profile settings.

Enable

– Choose this one to invoke this profile manually. In

addition to select Enable, you have to click Initiate under the
page of VPN-IPSec Tunnel-Policy Table.

Always-On

– Choose this one to invoke this profile

automatically by the system for every 30 seconds.

Disable

– Choose this one to inactivate this profile.

Name

The name for VPN connection (ex. “VPN1”). The maximum
length of name is 20 characters including spaces.

Authentication

The authentication to be used by PreShared Key or RSA
Signature.

PreShared Key

The shared key for peer identification. The maximum length is
40 characters, including spaces.

Security Protocol

AH -

Specify the IPSec protocol for the Authentication Header

protocol. The data will be authenticated but not be encrypted.

ESP -

Specify the IPSec protocol for the Encapsulating

Security Payload protocol. The data will be encrypted and

Summary of Contents for Vigor3300V+







































































































































































































































Search results

Summary of Contents for Vigor3300V+

Reviews:

Related manuals for Vigor3300V+

Brands by name

Popular brands

Draytek Vigor3300V+, User Manual

Search results

Summary of Contents for Vigor3300V+

Reviews:

Related manuals for Vigor3300V+

Brands by name

Popular brands