Draytek Vigor3300V+ User Manual Download

Page: 122 / 230

Vig Series User’s Guide

114

This page allows users to specify which subnet that DHCP server is located the relay agent
should redirect the DHCP request to.

WAN Interface

Choose the WAN interface for applying relay agent.

DHCP Server IP Address

Type the IP address for the DHCP server.

This page allows users to type in secondary IP address for connecting to a subnet. You can
set IP routing for each WAN interface respectively.

Status

Click

Enable

Disable

to activate or close the IP routing of

specific WAN interface.

IP Address

Type an IP address for the WAN interface
(WAN1/WAN2/WAN3/WAN4).

Subnet Mask

Type the subnet mask for the WAN interface
(WAN1/WAN2/WAN3/WAN4).

Summary of Contents for Vigor3300V+







































































































































































































































Search results

Summary of Contents for Vigor3300V+

Reviews:

Related manuals for Vigor3300V+

Brands by name

Popular brands

Draytek Vigor3300V+, User Manual

Search results

Summary of Contents for Vigor3300V+

Reviews:

Related manuals for Vigor3300V+

Brands by name

Popular brands