Page 3 of 4
Nocturne Exterior Projection Screen by Draper
www.draperinc.com
(765) 987-7999
Wiring Diagrams
Do not wire motorized units in parallel without written consent from Draper.
Wiring Diagrams Standard Motor)
Single Station Control
Internal Screen Wiring
White (Common)
Black (Down)
Red (Up)
Green/Yellow (Ground)
Dashed wiring
by electrician
Control
switch
Single gang box by others
Min. 4" x 2
1
/
8
" x 1
7
/
8
" deep
Blue
Black
Red
Location of key
operated on-off
switch if furnished
To 110-120V Line
Multiple Station Control
Internal Screen Wiring
White (Common)
Black (Down)
Red (Up)
Green/Yellow (Ground)
Dashed wiring
by electrician
Red
Red
Black
Blue
Blue
Cap off with wire
nut and tape
Black
Red
Blue
Black
Single gang box by others
Min. 4" x 2
1
/
8
" x 1
7
/
8
" deep.
3 shown. More or less equally
feasible.
Location of key
operated on-off
switch if furnished
To 110-120V Line
External Two-Way Serial Communication (RS232) with MC1
3 Button W
a
ll Switch
DO
WN - Blac
k
COM - White
UP - Red
White-Common to screen & 110-120V A
C
Neutr
al
Red-to screen (directional)
Bro
wn-to screen (directional)
Ye
llo
w
-to 110-120V A
C
-Hot
Blac
k-to 110-120V A
C-Hot
Green-Ground
Ey
e P
o
rt
fo
r IR Ey
e,
RF Receiv
e
r or LED
W
a
ll Switch.
F
o
r more than one of
these
, a splitter is required.
Au
x
P
o
rt
fo
r connecting additional L
VC-III
modules (up to six total can be link
ed-
connect from A
ux to Ey
e).
Dashed wir
ing b
y electr
ician
Lo
w v
oltage wir
ing b
y others
White (Common)
Red (Up)
Blac
k (Do
w
n)
Green (Ground)
Location of k
ey
oper
ated on-off
sw
itch if fur
nished
To
110-120V
Line
Inter
nal Screen Wir
ing
ST
OP
Control
Switches
24v DC
ST
OP
RS232 Data FROM Control System
RS232 Data TO Control System
Signal Ground & Manual Switch Common
Manual Switch Down
Manual Switch Up
White-Common to screen & 110-120V AC Neutral
Red-to Screen (directional)
Brown-to Screen (directional)
Black-Hot to 110-120V AC
Green/Yellow-Ground
Fuse
Program LED
Eye Port for IR Eye. For RF Receiver or LED
Wall Switch, a Splitter and a Power Supply
is required. Plug RF Receiver or LED Wall
Switch and Power Supply into splitter, then
run cable from Splitter to MC1 Eye Port.
Low Voltage Wiring by others
AC Wiring by electrician
MC1
White (Common)
Red (Up)
Black (Down)
Green/Yellow (Gnd)
Internal Screen Wiring
Location of key
operated on-off
switch if furnished
To
110-120V
Line
STOP
Control
Switches
24v DC
STOP
External Low Voltage and Remote Control
Please Note: Do not wire motors in parallel.
Internal Screen Wiring
White (Neutral)
Black
Green (Ground)
Dashed wiring
by electrician
To 110-120V Line
Wall Switch
or RF
Receiver
Radio Technology
110-120V Motor
CAUTION: Wall switches
provided with these screens are
interior switches, and should
not be installed outdoors.
