THE FOLLOWING ADDITIONAL INSTRUCTIONS MUST BE FOLLOWED AT ALL TIMES.
FAILURE TO DO SO COULD INVALIDATE THE GUARANTEE OF THIS SUBMERSIBLE WATER
PUMP.
1. The float switch must be clamped in position using cable clamp recess (see page 9, fig.10).
2. Clean water pumps are not suitable for use in dirty water.
3. These water pumps are designed for pumping water only.
The addition of any chemicals, chlorine or additives to the water could damage the pump, this
would be considered misuse and would not be covered under warranty.
4. When using clean water pumps in a pond or where there is gravel, mud, leaves, etc.
NOTE: The pump, should be suspended using a rope or chain or stood on a brick to prevent
any gravel, etc., being sucked into the pump.
5. If the pump fails to operate, disconnect from mains supply. Remove output elbow and turn the
impeller using a screwdriver or finger. Check for obstruction in the impeller, i.e. stones/gravel,
etc.
6. The float switch fitted to this pump is not suitable for continuous use as an on/off switch.
Important: ANY PUMP RETURNED TO DRAPER TOOLS UNDER WARRANTY MUST BE
CLEAN. IF A PUMP IS RECEIVED THAT IS NOT, OR HAS NOT BEEN CLEANED, IT WILL BE
RETURNED TO YOU AT YOUR COST.
5.3 CONNECTION TO THE POWER SUPPLY
Caution: Risk of electric shock. Do not open.
230V:
Make sure the power supply information on the machine’s rating plate are compatible with the
power supply you intend to connect it to.
This water pump comes supplied with a UK standard 3 pin plug fitted. It is designed for
connection to a domestic power supply rated at 230V AC.
Apart from replacing the fuse in the plug, no other electrical work is recommended on this
produce.
Important: If using an extension lead, follow the instructions that came with your lead regarding
maximum load while cable is wound. If in doubt, ensure that the entire cable is unwound. Using a
coiled extension lead will generate heat which could melt the lead and cause a fire.
5.2 GENERAL SAFETY INSTRUCTIONS FOR WATER BUTT PUMP USE
When carrying or lifting the submersible water butt pump always use the transport handle,
DO NOT carry or lift using the power cable.
The pump must not be used when people are in the water.
The pump must be supplied through a residual current device (RCD) having a rated residual
operating current not exceeding 30mA.
35°C maximum liquid temperature.
The electrical supply should be the same as that stated on the rating plate.
Submersible water pumps should always be transported, stored, and submersed vertically.
Always ensure that hands are dry when connecting and disconnecting the power supply.
Never operate the pump below the top of the water inlet.
The area being pumped should be kept clear, and nobody should enter the area while pump
is operating.
Important: PLEASE READ BEFORE USE:
The following additional instructions must be followed at all times. Failure to do so could
invalidate the guarantee of this submersible water pump.
Clean water pumps are NOT suitable for use in dirty water.
Note: The pump, should be suspended using a rope or chain or stood on a brick to prevent
any gravel etc. being sucked into the pump.
If pump fails to operate, disconnect from mains supply. Remove the base (see page 6) and
gently turn the impeller using a screwdriver. Check for obstruction in the impeller, i.e.
stones/gravel etc.
If the power cable becomes damaged it must be changed by the manufacturer or it’s service
agents.
Important: Any pump returned to Draper Tools Ltd under warranty must be CLEAN. If a
pump is received that has NOT been cleaned, it will be returned to you at your cost.
5.3 SPECIFIC SAFETY INSTRUCTIONS FOR PUMP USE
Have this tool repaired by a qualified person. This tool is designed to confirm to the relevant
international and local standards and as such should be maintained and repaired by someone
qualified; using only original parts supplied by the manufacturer: This will ensure the tool remains
safe to use.
1. Before connecting to the power supply:
i. A residual current circuit breaker (RCD) must be used for all applications.
ii. The electrical supply should be the same as stated on the rating plate.
2. Surface mounted pumps should always be transported and stored horizontally on the base
plate.
3. Always ensure that hands are dry when connecting and disconnecting the power supply.
4. Never operate the pump dry.
5. The area being pumped should be kept clear, nobody should enter area while pump is
operating.
5. HEALTH AND SAFETY INFORMATION
- 8 -
