D
Dräger Safety AG & Co. KGaA
– Revalstraße 1, D-23560 Lübeck, Germany
Tel. +49 451 8 82 - 27 94 – Fax +49 451 8 82 - 49 91
www.draeger.com
Polytron IR Transmitter Installation Instructions
Any use of the transmitter requires full understanding and strict observation of the
"Instructions for Use" of the Polytron Transmitter IR Ex (Part No. 90 23 655) or Polytron
Transmitter IR CO
2
/N
2
O (Part No. 90 23 656).
Installing Transmitter
The transmitter should always be mounted vertically (with the sensor pointing downwards) in a place where there is little vibration and minimum
changes of temperature, in the vicinity of a potential gas leak.
Secure in place by means of screws through the housing or use the mounting brackets (see drilling template). For maintenance purposes
allow at least 30 cm space below the transmitter.
When installing in explosion-hazard areas:
When wiring the transmitter to a central controller, the relevant regulations for the operation and installation of electrical equipment in
explosion-hazard areas must be observed (in Europe, EN 60079-14, in Germany VDE 0165).
Installing electrical connections
●
Connect to central controller by screened cable (braided screen cover
≥
80 %, outside diameter max. 15 mm).
The 0 V conductor (terminals K2 and K3) should be grounded in the controller.
●
To ensure optimum electromagnetic compatibility (EMC):
—
the transmitter should be grounded via one of the two grounding terminals. The screen should be connected to terminal E in the transmitter
and should not be grounded at the controller, or
—
the transmitter is not grounded via the external terminals. The screen should be connected to terminal E in the transmitter and grounded at
the controller.
Connecting the display unit or IR junction box for the hand-held terminal to the NDF version:
●
Connect the transmitter (NDF version) terminals K11, K12 and K13 and E to terminals K1, K2 and K3 and E of the display unit or IR junction
box: K13 to K1, K11 to K2 and K12 to K3.
The terminal cover (Ex-approved version) must be closed before starting up, otherwise the Ex-approval is invalid.
Technical Data (extract)
Three-wire type
●
Connect terminals K1 and K3 to the power supply (24 V ± 20 %,
300 mA).
Terminal K1 to + 24 V, terminal K3 to 0 V.
●
Connect terminal K4 to the 4 to 20 mA input of the central
controller.
Four-wire type
●
Connect terminals K1 and K2 to the power supply (24 V ± 20 %,
300 mA).
Terminal K1 to + 24 V, terminal K2 to 0 V.
●
Connect terminals K3 and K4 to the central controller. Connect
terminal K4 to the 4 to 20 mA input and terminal K3 to 0 V.
00
1
23654en
0022365
4en
Measuring range:
according to sensor model
Power consumption:
4 W
Signal transmission to central
controller:
4 to 20 mA
Power consumption IR Ex CO
2
and IR Ex HC:
2 W
Supply voltage:
24 V ±20 %, 300 mA
Protection type (EN 60 529):
IP 65
Cable entry:
PG 13.5 for 6 mm to 12 mm
cable diameter
Approval :
0158
DMT 02 ATEX E 178 X
II 2G EEx me [ib] d IIB + H
2
T4
IECEx BVS 05.0007
Ex me [ib] d IIB + H
2
T4
For details and safety precautions refer to the "Instructions for Use" of the Polytron Transmitter IR Ex (Part No. 90 23 655) or Polytron
Transmitter IR CO
2
/N
2
O (Part No. 90 23 656).
K1
K3
K4
E
K1
K3
K4
E
K1
K3
K4
E
K2
K1
K2
E
K3
K4
E
terminal cover
K1
K2
K3
K1
K2
K3
E
E
K1
K2
K3
K1 K2 K3
Transmitter (NDF Version)
Display unit
IR junction box
K13
K11
K12
K13
K11
K12
K13
K11
K12
K12
K11 K13
E
E
optionally
90 23 654
- MA 4675.600 en/de/fr/es
© Dräger Safety AG & Co. KGaA
4th edition - May 2006
Subject to alteration