background image

 

42

 

        

DR

®

 

 TRIMMER/MOWER

 

Parts List - Handlebar Assembly – PRO-XL SELF- PROPELLED 

NOTE:

 

Part numbers listed are available through DR Power Equipment.

 

Ref# Part# 

Description 

03 

143971 

Cable, Throttle, Reverse Throw, B&S 

04 

112381 

Washer, Flat, 1/4" USS 

05 

113081 

Ignition Switch, Key, E/S, w/805 
Hardware 

06 

174561 

Handlebar, Lower, Black 

07 

144641 

Bolt, Carriage, 5/16"-18 x 3", GR 2, ZP 

08 

110761 

Nut, Nylon Lock, 5/16"-18 

09 

147551 

Handlebar, Upper, Black 

09.1 191911 

Handlebar, 

Upper, Black, w/Grip 

10 

123361 

Bolt, 5/16"-18 x 1-1/4", HHCS, GR 5, ZP 

11 

174531 

Bracket, Key Switch, E/S 

12 

110731 

Nut, Nylon Lock, 1/4"-20 

13 

101451 

Bolt, 1/4"-20 x 1-1/2", HHCS, GR 2, ZP 

14 

112371 

Washer, Flat, #10, USS 

15 

143681 

Bracket, Cable, Trimmer Head Engage, 
Handlebar 

16 189721  Bail 

Bar 

17 143671  Stop, 

Bail 

Bar 

 

Ref# Part# 

Description 

18 190471  Grip, 

Handlebar, 

Textured Vinyl, 18-3/4" 

Long 

19 

143931 

Spring, C, .720" OD x .063" Wire, 
Handlebar Adjuster 

20 

143661 

Knob, Handlebar, 5/16"-18 

21 191351  Adjuster, 

Handlebar, 

Inside 

22 143731  Adjuster, 

Handlebar, 

Outside 

22.1 145801 

Adjuster 

Assembly, 

Handlebar 

23 

112141 

Tie, Cable, 7-1/2" Long, Black 

24 179641  Cable, 

Transmission 

25 

114561 

Bolt, 1/4"-20 x 2.0", HCS 

26 

190011 

Cable, Trimmer Head Engage 

27 179651  Lever, 

Transmission 

Engage 

28 214661  O-Ring 

Not Illustrated 

 

188241 

Wire Harness, w/adapter 

 

Summary of Contents for SPRINT PRO





















































Reviews: