background image

 

 

COUNTRY HOME PRODUCTS, Inc. 

M E I G S   R O A D ,   P . O .   B O X   2 5 ,   V E R G E N N E S ,   V E R M O N T   0 5 4 9 1  

1-800-DR-OWNER (376-9637) • www.dr-owner.com 

©2002 CHP, Inc. 151751

 

 

 

Warranty 

2-Year Limited Warranty 

Terms and Conditions

 

The 

DR

®

 10 HP CHIPPER is warranted for two (2) years against defects in materials or workmanship when put to ordinary 

and normal consumer use; ninety (90) days for any other use.  The engine manufacturer warrants the engine separately. 

For the purposes of all the above warranties, “ordinary and normal consumer use” refers to non-commercial residential use 
and does not include misuse, accidents or damage due to inadequate maintenance. 

Country Home Products, Inc. (home of 

DR

®

 Power Equipment) certifies that the 

DR

®

 10 HP CHIPPER is fit for ordinary 

purposes for which a product of this type is used.  Country Home Products, Inc. however, limits the implied warranties of 
merchantability and fitness in duration to a period of two (2) years in consumer use, ninety (90) days for any other use.

 

The 2-Year Limited Warranty on the 

DR

®

 10 HP CHIPPER starts on the date the machine ships from our factory.  The 2-Year 

Limited Warranty is applicable only to the original owner. 

The warranty holder is responsible for the performance of the required maintenance as defined by the manufacturer's owner's 
manuals.  The warranty holder is responsible for replacement of normally wearing parts such as the drive belt, knife, Wear Plate, 
bearings, and flex guards.  Attachments and accessories to the machine are not covered by this warranty. 

During the warranty period, the warranty holder is responsible for the machine transportation charges, if required.  During the 
warranty period, warranty parts will be shipped by standard method at no charge to the warranty holder.  Expedited shipping of 
warranty parts is the responsibility of the warranty holder. 

SOME STATES DO NOT ALLOW LIMITATIONS ON THE LENGTH OF IMPLIED WARRANTIES, SO THE ABOVE LIMITATIONS 
MAY NOT APPLY TO YOU.

 

Country Home Products, Inc. shall not be liable under any circumstances for any 

incidental or consequential damages or 

expenses 

of any kind, including, but not limited to, cost of equipment rentals, loss of profit, or cost of hiring services to 

perform tasks normally performed by the 

DR

®

 10 HP CHIPPER.

 

SOME STATES DO NOT ALLOW THE EXCLUSION OR LIMITATION OF INCIDENTAL OR CONSEQUENTIAL DAMAGES, SO 
THE ABOVE LIMITATIONS MAY NOT APPLY TO YOU. 

Customer Service Hotline 

Country Home Products, Inc.’s objective is to have 100% satisfied customers. For that reason, we operate a 6-day-a-week 
Technical Service Department for our Owners. You can access a Representative by dialing our TOLL-FREE Hotline at 

1-800-

DR-OWNER (376-9637).

 The sole job of our well-trained and friendly folks is to ensure that you get any help you need in a 

timely fashion. They are there to answer all your questions including: (1) inquiries on any of the above warranties, (2) 
inquiries about replacement parts, or (3) your questions regarding service, maintenance and operation. 

Our Customer Service Representatives will also be happy to answer any of your questions regarding the separate warranties 
on all engines. However, to obtain service, repair or replacement of any engine within the time period covered by the 
manufacturer’s limited warranty, follow the instructions and warranty information specifically pertaining to those items 
provided by their separate manufacturers.

 

THIS WARRANTY GIVES YOU SPECIFIC LEGAL RIGHTS, AND YOU HAVE OTHER RIGHTS, WHICH VARY FROM STATE TO 
STATE. 

 

DR

®

 

10 HP CHIPPER

 

Summary of Contents for 10 HP CHIPPER





















































Reviews: