background image

 

 

- 11 -

-

  In the minimum reading Mode, press the + key to display the following minimum 

values together with the time and date at which these values were recorded, if 
press SET key for 2 seconds in the following individual minimum value will be reset 
to current reading:   

1.  Indoor humidity minimum 
2.  Indoor temperature minimum 
3.  Outdoor humidity minimum 
4.  Outdoor temperature minimum  
5.  Outdoor dewpoint minimum 
6.  Pressure minimum 
 

-  Press the SNOOZE/LIGHT key or key idle 10 second, the Min/Max mode will return 

to Normal Mode 

 

 

6. Problems and interference with operation 

 

Problem & cause 

Remedy 

Distance between transmitters 
and receiver too long 

Reduce distance between transmitters and 
receiver to receive signal 

High shielding materials between 
the units (thick walls, steel, 
concrete, isolating aluminum foil 
and etc.) 

Find a different location for sensors and/or 
receiver. See also item ‘transmission range’ 
below 
 

Interference from other sources 
(e.g. wireless radio, headset, 
speaker, etc. operating on the 
same frequency) 

Find a different location for the sensors and/or 
base station. Neighbors using electrical devices 
operation on the same signal frequency can also 
cause interference with reception 

No reception after adding 
extension cables 

Find a new location for the sensors and/or base 
station.  

Poor contrast LCD or no 
reception or low batteries in 
sensors or receiver 

Change batteries   

Temperature, humidity, or air 
pressure is incorrect. 
 
 

Check/replace batteries. If multiple remote 
sensors are in use, check location with 
corresponding “boxed numbers”. Or move away 
from sources of heat/cold. Adjust relative air 
pressure to a value from a reliable source (TV 
radio, etc.).   

 

 

 

 

 

 

 

 

 

Summary of Contents for WH1170













Reviews: