background image

4

 

        

DR

® 

PTO POST HOLE DIGGER

 

Protecting yourself and those around you 

Operating the Post Hole Digger Safely 

This is a high-powered machine, with moving parts operating with high energy at high speeds.  You must operate the machine 
safely.  Unsafe operation can create a number of hazards for you, as well as anyone else in the nearby area.  Always take the 
following precautions when using this machine: 

 

Know how to stop the Post Hole Digger quickly by disengaging the PTO Shaft and shutting down the tractor. 

 

Never allow people who are unfamiliar with these instructions to use the DR PTO Post Hole Digger.  Allow only responsible 
individuals who are familiar with these rules of safe operation to use your machine. 

 

Operate this Post Hole Digger from the tractor seat only. Make sure that the tractor engine is shut off and the PTO drive is 
disengaged before leaving the tractor seat. 

 

ALWAYS make sure that the Tractor Brake is set before Digging a hole. 

 

NEVER move the tractor with the power-take-off in the ON position. 

 

Only one person should operate the Post Hole Digger.

 

 

Make sure that the auger point and cutting edges are intact and in good working order before using this Post Hole Digger. 

 

Your DR PTO Post Hole Digger is a powerful tool, not a plaything.  Exercise extreme caution at all times.  The design of your 
machine is for digging holes.  Do not use it for any other purpose. 

 

Whenever you leave the operating position to make adjustments, maintain blades, or if you have to remove grass or debris 
from the Auger, always disengage the PTO, shut down the Tractor Engine, remove the Key, wait for all moving parts to come 
to a complete stop, disconnect the PTO shaft from the Tractor, then wait five minutes before performing any maintenance 
procedure or inspection on the Post Hole Digger. 

 

This machine is designed to operate at 540 rpm PTO Shaft speed only!  Never operate at a faster speed; doing so can cause 
serious injury to the operator or bystanders and could cause damage to the machine that is not covered under warranty. 

 

NEVER operate the post hole digger with the auger point more than 6 inches above ground level. Operating the Post Hole 
D

igger in elevated positions may cause the PTO “U” joints to bind resulting in equipment damage and operator injury.

 

This is a high-powered machine, with moving parts operating with high energy at high speeds.  You must operate the machine 
safely.  Unsafe operation can create a number of hazards for you, as well as anyone else in the nearby area.  Always take the 
following precautions when using this machine: 

 

Keep in mind that the operator or user is responsible for accidents or hazards occurring to other people, their property, and 
themselves. 

 

Always wear protective goggles or safety glasses with side shields while operating the Post Hole Digger to protect your eyes 
from possible thrown debris. 

 

Avoid wearin

g loose clothing or jewelry, which can catch on the machine’s moving parts.

 

 

Use ear protectors or ear plugs rated for at least 20 dba to protect your hearing. 

 

NEVER attach the post hole digger with the tractor engine running. 

 

Never tamper with safety devices.  Check their proper operation regularly. 

 

Never operate the machine when under the influence of alcohol, drugs, or medication. 

Summary of Contents for PTO POST HOLE DIGGER

















Reviews: