A11
THERMOSTAT INSTRUCTIONS
To obtain a very good thermal stability, we use a digital temperature controller with thermocouple.
The Omron E5CS thermostat controls the heat of every element at the SP (set point).
The temperature of the oven is always shown on the display of the thermostat and an arrow indicates
if the temperature is over or below the SP. When the green light is lit, it indicates that the temperature
is at the SP ± 1 %.
To adjust the SP (set point) value, you just have to press the key on the left and use the up and down
keys to set the temperature. Press the left key to return to run mode.
COOLING FAN
A cooling fan located on front top of the oven run during normal operation of the oven.
A temperature detector (thermodisk) is installed in the control compartment to start the cooling
fan when the temperature rises over 37°C.
PIZ3G FAULT DESCRIPTION
When there is a fault, a buzzer rings and the red light "fault" turns on
It may be caused by
•
Too much pressure in burner compartment (blower does not work or does not produce
vacuum) , air pressure switch is not well adjusted or defective.
•
Gas pressure is too low or not well adjusted or defective gas pressure switch.
•
Malfunction of ignition system or detection of flame.
To correct press the red push button "fault" (same one as the "fault" light) for two second.
If the fault is still active and cannot be reset, call for service.
COOKING TIMER
Set the baking time required with the small push button on the timer. The green display is the setting
time and the red display is the countdown time (Ex: 25 minutes = set 2500 on green display).
After setting: Push the
START/STOP
button then, when the time expires, the buzzer will ring.
Push the
START/STOP
button again to stop the buzzer.
If you want to restart the time in the middle of the countdown, press on the
START/STOP
button.
P.S.
The timer is simply a reminder for the approximate duration of the baking time..
POWER FAILURE
The burner, the electric gas valve and the regulator are all designed to be fail safe. Then, there is
no special action to take in case of electrical power failure. Turn off the oven. Never leave the
oven unsupervised when the power is on the unit.
Summary of Contents for PIZ3G
