Dover PSG Wilden PRO-FLO P1500 Engineering Operation & Maintenance Manual Download Page 2

 

WIL-11160-E-10  

P1500 Bolted Plastic 

Copyright 

Copyright 2018 PSG

®

, a Dover Company. All rights reserved. 

 
PSG reserves the right to modify the information and illustrations in this document without prior 
notice. The product described in this document is furnished under a license agreement or 
nondisclosure agreement. No part of this document may be reproduced, stored in a retrieval 
system, or transmitted in any form or any means electronic or mechanical, including 
photocopying and recording, without the written permission of PSG, a Dover Company, except 
as described by the terms of those agreements. 
 
This is a non-contractual document.  
 

Trademarks 

PSG and the PSG logo are registered trademarks of PSG. Wilden

®

 is a registered trademark of 

PSG California LLC. Pro-Flo

®

 SHIFT and Pro-Flo

®

 are registered trademarks of PSG California 

LLC. Wil-Flex

®

 is a trademark of PSG California LLC. Saniflex™ is a trademark of PSG 

California LLC. 
 
All trademarks, names, logos and service marks (collectively “trademarks”) in this document are 
registered and unregistered trademarks of their respective owners. Nothing contained in this 
document should be construed as granting any license or right to use any trademark without the 
prior written permission of the trademark owner. 
 

Warranty 

Each and every product manufactured by Wilden is built to meet the highest standards of 
quality. Every pump is functionally tested to ensure integrity of operation. Wilden warrants that 
pumps, accessories and parts manufactured or supplied by it to be free from defects in material 
and workmanship for a period of five (5) years from date of installation or six (6) years from date 
of manufacture, whichever comes first. 
 
For more information, and to register your Wilden pump for warranty, please visit 
https://www.psgdover.com/wilden/support/warranty-registration. 
 

Certifications 
 
 
 
 
 
 
 
 

 

Summary of Contents for PSG Wilden PRO-FLO P1500

























Reviews: