Dover IMAJE Jaime 1000 Series Manual Download

Page: 13 / 125

5.2

Configuration of the jumpers on the Industrial Interface board

The jumpers on the Industrial Interface board allow configuration of the serial connection.

• RXD allows selection of the transmission mode

- Position 232: voltage levels transmission,
- Position 20 mA: loop transmission.

• SW1 used only in "loop" transmission

- Postion active: active transmission,
- Position passsive: passive transmission.

• SW2 used only in "loop" transmission

- Position active: active reception,
- Position passive: passive reception.

NOTE

If the computer is configured in active the printer must be configured
in passive on the corresponding line, and vice versa.

• CTS

- Position DSR: The printer will only transmit data if the computer gives instructions to send

(DSR active) (CTS linked to DSR).

- Position CTS: The printer will only transmit data if the computer activates the CTS.
- Position GND: The printer can transmit continually (CTS linked to 0 V).
- Position RTS: The printer can transmit continually (CTS linked to RTS).

Figure 1 :

Location of jumpers on the Industrial Interface Card

Figure 1

General

Page 2-6

A13862 Version E

Summary of Contents for IMAJE Jaime 1000 Series






























































































































Search results

Summary of Contents for IMAJE Jaime 1000 Series

Reviews:

Related manuals for IMAJE Jaime 1000 Series

Brands by name

Popular brands

Dover IMAJE Jaime 1000 Series, Manual

Search results

Summary of Contents for IMAJE Jaime 1000 Series

Reviews:

Related manuals for IMAJE Jaime 1000 Series

Brands by name

Popular brands