manualshive.com logo in svg

Dover Blackmer TYPHON 1000, Manual, Page: 19 / 21

Share
Download
Dover Blackmer TYPHON 1000 Manual Download Page 19

19/21

NT 1401-F00 12.05 Cold front outlet Intercooler TYPHON e

55..  S

SP

PA

AR

RE

E  P

PA

AR

RT

TS

S  ((ccoonnttiinnuuoouuss))

Référence

Désignation

Quantité

Remarques

312112

Kit filtre à huile

1

Pièce détachée compresseur

216404

Cartouche filtrante

2

312569

Kit fixation : filtre

1

312568

Kit fixation : silencieux

1

312570

Kit fixation : échangeur

1

219842

Thermocontact

1

312567

Matériel électrique interne

1

312534

Clapet anti-retour 2.3 bar

1

312637

Clapet anti-retour 2.0 bar

1

312535

Soupape

1

312523

Ensemble instrumentation

1

Référence

Rapport 1:1

Rapport 1:1,12

Rapport 1:1,25

Rapport 1:1,4

Kit poulie & courroie

312287

312316

312553

312317

PART  LIST  FOR  INTERCOOLER  PACKAGE,  NOT  INCLUDED  IN  THE  PREVIOUS  EXPLODED  VIEW

NOTE - To order spare parts specify :

•

  The PART NUMBER and SERIAL NUMBER of the package (stamped on an identification plate)

•

  The reference to the current INSTRUCTIONS N° 1401-F00 with its revision number

•

  REFERENCE and QUANTITY wanted for each part.

Summary of Contents for Blackmer TYPHON 1000






















Reviews:

No comments