1.
1121-1349
1
Lid & Caution Label
2.
1121-1075
1
Basket/Weight
3.
1121-1203
1
Element, 20 Sq. Ft.
4.
343-1042
1
Blaster Nozzle w/Washer
5.
340-1232
1
Light Oak Cover
6.
308-1054
1
O-Ring Drain Valve
7.
340-1246
1
Drain Valve
8.
307-1001
1
Gasket, Drain Cap
9.
340-1035
1
Drain Cap
10.*
1121-1318
1
Skim Filter Body Assy.
11.
387-1003
4
1 1/2" Wire Hose Clamp
12.
346-1035
2
Hose, 1 1/2" x 8'
13.
340-1238
1
Return Fitting Cover
14.
348-1030
1
Eyball w/Flow Control
15.
340-1278
1
Eyeball Insert
16.
340-1240
1
Shut-Off Disk
17.
340-1237
1
Return Fitting Adaptor
PARTS LIST — MODEL NO. 0-1120-000
ITEM
P/N
QTY
DESCRIPTION
ITEM
P/N
QTY
DESCRIPTION
18.
308-1110
2
Return Fitting Gasket
19
340-1773
1
Return Fitting Body
20.
330-1008
4
#8 x 1/2" Screw
21.
340-1253
1
Vacuum Hose Adaptor
22.
340-1271
1
Vac Port Cover Retainer
23.
348-1028
1
Vac Port Cover
24.
340-1248
2
Support Brace
25.
330-1004
15
#12 x 27/32" Screw
26.
340-1274
1
Faceplate (Skim-Line)
27.
307-1027
2
Skim-Line Faceplate Gasket
28.
340-1173
1
Weir Hinge
29.
1119-1032
1
Weir Float
30.
1119-1033
1
Weir Assembly
31.
365-1531
1
Owner's Guide
32.
—
1
Warranty Card
33.
360-1461
1
Operating Instructions Label
34.
360-1634
1
Caution Label
* Skim Filter Body Assembly (item 10 above) includes items 5, 6, 7, 8, 9 and 33.
4.
The lid (1) performs two functions. In normal posi-
tion, it covers the top of the filter. During vacuum-
ing, this same lid becomes the sealing plate for the
vacuuming. Be sure pump is "OFF". Remove the
lid and lower it inside (handle grip up) to rest on the
rectangular hole above basket. Make sure air is not
trapped under the lid. Trapped air will cause the lid
to rise.
CAUTION: Never attempt to install the lid in the
vacuuming position while your Pool Power Pak is
running. The lid may suddenly be drawn down into
position due to the pump's high suction action. You
may injure your hands or fingers.
5.
With the lid in place, start pump and operate
vacuum over pool floor.
6.
When finished vacuuming, stop pump . Remove
vacuum hose with vacuum adaptor attached from
the pool. Clean skimmer basket and element.
Move lid to the original position on top of the filter.
Start pump to resume normal filtering operation.
6
WINTERIZING (FREEZING CLIMATES)
We strongly recommend, for the protection of your filter,
liner and pool wall, that you purchase and install the
DOUGHBOY Winterizing Kit (0-2099-001). The proper
installation of this kit will allow the removal and storage
of your filter and should eliminate any possibility of
damage due to winter peril. CAUTION: Removing the
Skim-Filter without installing a Winterizing Kit is very
dangerous to the pool wall, liner and pool installation,
and voids any warranty. Filter damage caused by
freezing temperatures is not covered by product
warranty.
1.
Drain pool to 6 inches below the eyeball return
fitting.
2.
Remove, clean and store in warm area: basket,
element, hoses and Pool Power Pak.
3.
Remove filter from pool, clean and store. Install the
DOUGHBOY Winterizing Kit per Kit instructions.
4.
Remove the return fitting eyeball by unscrewing the
cover. Replace the eyeball with the shut-off disc
(16) and reinstall the cover. NOTE: This shut-off
disc can be useful for plugging off the return fitting
should maintenance be required on the filter or
Power Pak.
5.
For spring start-up, follow instructions under
INSTALLATION in this guide.
