background image

4

ED250

01-2018

DL4614-080

dormakaba ED250 IG Service Manual

Chapter 2

2  Product description

2.1  Intended use

The ED250 is an electromechanical operator used 
exclusively for opening and closing interior or exterior 
swing doors.

The ED250 in-ground operator is packaged in a cement 
case for in-ground floor installations. 
For double swing doors, two cement cases are supplied.

2.2  ED250 full energy operator

ED250 is supplied as a full energy operator.
The operator can be configured as a low energy 
operator by parameter adjustment.

WARNING

For low energy applications, ED250 parameters 
must be adjusted to meet ANSI/BHMA A156.19 
specifications. Reference:
•  Chapter 17, Parameters
•  Chapter 16, ANSI/BHMA standards

 

2.3  Arm configurations

Door width

ED250

Inches

mm

Pounds

kg

28

711.2

882

400

32

812.8

882

400

36

914.4

882

400

39

990.6

882

400

42

1067

882

400

48

1219

700

340

2.5  Maximum door weights

TIPS AND RECOMMENDATIONS

Insure operator is qualified for use at the 
respective smoke or fire-rated door.

2.4  Cement case enclosure

The cement case enclosure is listed and labeled to: 
•  UL50, NEMA 4 water resistant enclosure
•  CSA 22.2

2.5  Floor threshold

1.  Threshold to cover cement case and blockout is not 

supplied with the ED250 in-ground package. 
Threshold installation and maintenance is customer 
responsibility. Refer to Chapter 8 for threshold 
maintenance.

Fig. 2.1.1  In-ground case with ED250 operator

Fig. 2.3.3  Arm and track assembly (track in door)

Fig. 2.3.1  Center hung

Fig. 2.3.2  Offset pivot

Fig. 2.3.4  Floor threshold

1

 Track

2

 Slide

1

2

3

4

3

 Arm

4

  M8 shoulder screw

Threshold

Cement case cover

Blockout

Summary of Contents for ED250





























































Reviews: