Doosan 50001 Shop Manual Download

Page: 170 / 898

SP001625

Track Assembly
Page 24

Disassembly

Refer to "Track Disassembly" to remove track and idler
assembly.

Remove spring pin (7) from support (3).

Remove support (3) from shaft (2).

Remove O-ring (6) using a screwdriver (-).

•

Once removed, O-ring (6) should not be reused.

Remove floating seal (5), bushing (4), shaft (2) and plug (8).

Reassembly

For reassembly, reverse disassembly procedures.

•

Clean separated parts.

•

Coat clean gear oil or engine oil (80.0 cc (2.71 oz))
before assembling oil seal (5).

•

See “Track Installation” on page -20. for track
reassembly.

Summary of Contents for 50001



































































































































































































































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for 50001

Reviews:

Related manuals for 50001

Brands by name

Popular brands

Doosan 50001, Shop Manual

Search results

Summary of Contents for 50001

Reviews:

Related manuals for 50001

Brands by name

Popular brands