background image

1506-065-F-3-14  

Page 

5

 

Table of Contents 

 

IMPORTANT NOTICES............................................................................................................................................6 

 

SECTION 1 – INSTALLATION 

1.1 Mounting 

Dimensions ...............................................................................................................................7 

1.2 Wiring .......................................................................................................................................................9 

1.3 Wire 

Diagram............................................................................................................................................10 

1.4 Terminal 

Identification ..............................................................................................................................11 

1.5 

Aiphone Intercom Station Connections ....................................................................................................12 

1.6 

Secondary Keypad Wiring ........................................................................................................................13 

 

SECTION 2 – PROGRAMMING 

2.1 Master 

Code .............................................................................................................................................15 

2.2 

Relay Strike Time .....................................................................................................................................15 

2.3 X-Strikes 

Programming ............................................................................................................................15 

2.4 

Programming Four-digit Entry Codes .......................................................................................................16 

2.5 

Erasing Individual Four-digit Entry Codes ................................................................................................16 

2.6 

Erasing ALL Four-digit Entry Codes .........................................................................................................16 

2.7 

Four-digit entry Code Divide Number .......................................................................................................16 

2.8 

Programming Five-digit Entry Codes .......................................................................................................17 

2.9 

Erasing Individual Five-digit Entry Codes.................................................................................................17 

2.10 

Erasing ALL Five-digit Entry Codes .........................................................................................................17 

2.11 

Five-digit Entry Code Divide Number .......................................................................................................17 

2.12 

Hold Boundary Programming ...................................................................................................................18 

2.13 

Time Zone 1 Boundary Programming ......................................................................................................18 

2.14 

Time Zone 2 Boundary Programming ......................................................................................................18 

 

SECTION 3 – OPERATING INSTRUCTIONS 

3.1 Four-digit 

Entry 

Codes..............................................................................................................................19 

3.2 

Five-digit Entry Codes ..............................................................................................................................19 

3.3 

Request to Exit Input ................................................................................................................................19 

3.4 Door 

Open 

Input .......................................................................................................................................19 

3.5 

Hold Feature Operation ............................................................................................................................20 

3.6 Time 

Zone 

Operation ...............................................................................................................................21 

 

SECTION 4 – APPENDIX 

4.1 Troubleshooting........................................................................................................................................23 

4.2 Data 

Tables ..............................................................................................................................................24 

 

Log Sheet .................................................................................................................................................................25 

Summary of Contents for 1504-080


























Reviews: