DoorHan SLIDING-1300 Installation And Operation Manual Download Page 4

4

2. SAFETY PRECAUTIONS

WARNING!

 Important safety instructions. Follow all instructions since incorrect installation can lead to 

severe injury.

 

y

Follow any instructions of this manual as improper equipment installation could result in serious damage.

 

y

Sliding-1300/2100 drive serves to automatic control of sliding door. Use the drive as intended only, any misuse of 
the drive is forbidden.

 

y

DoorHan is not responsible for any personal injury in case of the product misuse.

 

y

Prior to drive installation, make sure the door operates smoothly.

 

y

Installation shall be carried out according to the standards EN 12453 and EN 12445. These requirements shall be 
complied with in countries outside the EU to ensure the required safety level.

 

y

Check if the door complies with standards EN 12604 and EN 12605 (see the door documentation).

 

y

These requirements shall be complied with in countries outside the EU to ensure the required safety level.

 

y

Mechanical joints of the door shall meet the requirements of standards EN 12604 and EN 12605.

 

y

Prior to drive installation, make sure the installation site complies with the drive specifications in climatic conditions.

 

y

Do not install the equipment in the premises with inflammables or any other hazardous environments, as this could 
result in explosion or fire.

 

y

Use the tools specified in section “Tools” hereof during drive assembly, installation and adjustment.

 

y

Use a steady foot when working at height.

 

y

Use protective devices for your hands and face when drilling the holes.

 

y

Use the hardware supplied in a complete set of the drive or other appropriate hardware to fix the product.

 

y

It is necessary to disconnect the power supply during installation, cleaning or maintenance.

 

y

It is necessary to install an additional safety device to prevent the drive activation with an open gate when installing 
the drive on a door with gate.

 

y

Use DoorHan original accessories, as third-party accessories can result in failure of automatic system.

 

y

DoorHan is not responsible for the unstable operation of automatic system when using third-party safety devices 
and accessories without prior approval of DoorHan.

 

y

Do not leave the motors in released position. It can result in out-of-control door leaf movement and, as a consequence, 
to is damage.

 

y

Do not drive, if the device requires repair or adjustment as defects in drive installation or improper installation of the 
door can result in injury.

 

y

DoorHan bears no responsibility if the product is installed improperly and damaged during operation.

 

y

The drive is not equipped with a fixed power cord, so the power shall be supplied to automatic system through the 
circuit breaker following at least 3 mm distance between adjacent contacts. It’s recommended to use a double-pole 
circuit breaker of 10 A.

 

y

Make sure there are no obstacles in the drive operating area before its running.

 

y

Do not make any changes to the automatic system, not specified in this manual.

 

y

Remove the product package and dispose it. Do not leave the packaging materials within reach of children.

 

y

Never allow children to play in the door operating area during drive operation. Any remote controllers and fixed 
buttons to operate the drive shall be prevented from possible use by children.

 

y

Drive and entry are permitted only at the door stopped and the drive turned off.

 

y

The content of this manual cannot serve as a basis for any claims.

 

y

The manufacturing company reserves the right to make changes in design and improve it without prior notice.

 

y

Frequently examine the installation, in particular check cables, springs and mountings for signs of wear, damage 
or imbalance. Do not use if repair or adjustment is needed since a fault in the installation or an incorrectly balanced 
door may cause injury; 

 

y

Install any fixed control at a height of at least 1,5 m and within sight of the door but away from moving parts 

 

y

Permanently fix the labels warning against entrapment in a prominent place or near any fixed controls 

 

y

This appliance is not intended for use by persons (including children) with reduced physical, sensory or mental 
capabilities, or lack of experience and knowledge, unless they have been given supervision or instruction concerning 
use of the appliance by a person responsible for their safety

WARNING! It’s required to install a mechanical stop to limit the stroke of the door leaf to ensure safe and proper 
operation of the drive.

4.2. Drive installation and cabling diagram

SAFETY PRECAUTIONS

Summary of Contents for SLIDING-1300













Reviews: