background image

7

4.4.  TRACK INSTALLATION

The operator suspension height is determined by the maximum lift of upper edge of the door leaf. After preliminary assembly 

(see p. 4.3) you can start to install the track:

1.   If it is required to shorten a guide, it is necessary to fulfill operations, described in Appendix 1.
2.  You should mark a vertical line, corresponding to the horizontal door centre (fig. 5).
3.   You should place a lintel mounting bracket (1) in such a way that the distance from upper edge of the open door leaf to lower 

edge of the track amounted to minimum 10 mm (fig. 5.2) and fix it to the lintel using self-tapping screws (2) (fig. 5.1).

4.  You should fasten the track (3) and the lintel mounting bracket by means of a track fixation bolt (4) (fig. 5.3).
5.  You should install a U-shaped bracket (5) on the track approximately at a distance 2/3 L and attach it to the ceiling (fig. 5.4).
6.   You should install track mounting brackets (6) on the track approximately at a distance 1/3 L and attach them to the 

ceiling (fig. 5.5).

7.   You should install a rod-to-leaf mounting bracket (7) in the middle of the upper aluminium profile of the door leaf and fix 

it using self-tapping screws (8) (fig. 5.6).

8.   You  should  attach  a  cranked  rod  (9)  to  the  rod  mounting  bracket  and  fix  it  by  means  of  a  pin  axle  (10)  (fig.  5.7). 

It is allowed not to mount the cranked rod, if 

α

 angle is observed.

1

1. 

Lintel mounting bracket

2. 

Anchor bolt

3. 

Track

4. 

Track fixation bolt

5. 

U-shaped bracket

6. 

Track mounting bracket

7. 

Rod-to-leaf mounting bracket

8. 

Screw 6x15

9. 

Cranked rod

10.  Pin axle

10

2

3

4

6

9

10

Pic. 5

5.1

5.2

5.3

5.5

5.7

α

Door

Wall

B/2

B

α

30° < 

α

 < 60°

L

1/3L

2/3L

5

5.4

7

8

5.6

OPERATOR INSTALLATION

Summary of Contents for SECTIONAL-500PRO



















Reviews: