background image

IOM 7568201 (ENG), Revision 3 (June 2019) ©2003 Donaldson Company, Inc.  

Donaldson, Torit, EZ Filter Pack, and the color blue are marks of Donaldson Company, Inc. All other marks belong to their respective owners.

Donaldson Company, Inc. 

Minneapolis, MN

donaldsontorit.com • shop.donaldson.com

North America

Email: [email protected]  

Phone: (USA): 800-365-1331 • (MX): 800-343-3639

Australasia

Email: [email protected] 

Phone: +61 2 4350 2000 

Toll Free: (AU) 1800 345 837 • (NZ) 0800 743 387

China IAF

Email: [email protected] 

Phone: (86) 400-820-1038

Donaldson Europe B.V.B.A.

Email: [email protected] 

Phone: + 32 (0) 16 38 38 11

India

Email: [email protected] 

Phone: +91 124 4807400 

Toll Free: 18001035018

Latinoamerica

Email: [email protected] 

Phone: +52 449 300 2442

South Africa

Email: [email protected] 

Phone: +27 11 997 6000

Southeast Asia IAF

Email: [email protected] 

Phone: (65) 63117373

Important Notice

Many factors beyond the control of Donaldson can affect the use and performance of Donaldson products in a particular application, including the conditions under which the product is used. Since these 

factors are uniquely within the user’s knowledge and control, it is essential the user evaluate the products to determine whether the product is fit for the particular purpose and suitable for the user’s application. 

All products, product specifications, availability and data are subject to change without notice, and may vary by region or country.

Significantly improve the performance of your collector with genuine Donaldson Torit 
replacement filters and parts. 

Call Donaldson Torit at 800-365-1331.

Summary of Contents for Torit DB-800





















Reviews: