manualshive.com logo in svg

DOMUSA TEKNIK LIGNUM NG 20, Installation And Operating Instructions Manual

Share
Download
DOMUSA TEKNIK LIGNUM NG 20 Installation And Operating Instructions Manual Download Page 12

Lignum NG

 

 

10 

 

 

IMPORTANT:  Before carrying out any work on the boiler's electrical installation, always ensure 

it is disconnected from the mains. 

IMPORTANT: Make 

sure 

that none of the mains cables come into contact with a hot surface 

(e.g. flue). 

3.8

 

Example of an installation with a buffer tank 

The Lignum NG boiler is equipped with an electronic control that can govern a circuit with buffer 

tank, with an external circulation kit to prevent condensation in the heat exchanger. The heating 

circuit must be regulated and controlled with an external regulator (not included in the boiler 

control). 

The figure below shows an example of a hydraulic diagram of a buffer tank heating installation: 

 

 

 VS

:

  Heating safety valve 

 VR

:

  Anti-condensation thermostatic valve 

 VA:

 Drain valve 

 BC

:

 Heating pump 

 BT:

  Buffer tank

 VDT:

  Temperature relief 

valve 

 VC:

  Heating expansion vessel 

 BCD:

  Direct circuit pump 

 BCM:

  Mixed circuit pump 

      P:

  Automatic air bleed valve 

IMPORTANT: It is obligatory and essential to install a heating water buffer tank. 

Summary of Contents for LIGNUM NG 20













































Reviews:

No comments

Brands by name

Popular brands

Load more brands