DOMUSA TEKNIK EVOLUTION SOLAR HFD Installation And Operating Instructions Manual Download Page 22

Page: 22 / 56

Evolution Solar HFD

TEMPERATURE SELECTION

10.1

Selecting the boiler setpoint temperature



The desired boiler operating temperature is selected using the touch button, as shown in the
figure. To select the desired temperature, touch the "

" or "

" symbols to increase or decrease the

temperature respectively. When the temperature has been selected, the display will return to

standby mode after a few seconds.

The boiler setpoint temperature can also be selected by using the MODE touch button to browse to

the “

boiler setpoint temperature

" display option. When the display shows this option, touch the "+

/-" symbols to select the desired temperature.

If you wish to totally disable the boiler heating function (

Summer

mode), select the setpoint value

OFF

" by touching the "-" symbol until this value appears on the display.

The permitted boiler setpoint temperature range is OFF and 30 - 85 ºC.

Evolution

model boilers are

condensing boilers. In order to obtain maximum boiler performance and energy savings, it is

therefore recommended to select a setpoint temperature of 55-70 ºC, providing this is permitted by

the heating system installed and the insulation conditions of your home.

10.2

Selecting the back-up DHW setpoint temperature



The desired DHW temperature is selected using the touch button, as shown in the figure. To select
the desired temperature, touch the "

" or "

" symbols to increase or decrease the temperature

respectively. When the temperature has been selected, the display will return to standby mode

after a few seconds. The DHW setpoint temperature range permitted is OFF and 30 - 65 ºC.

The DHW setpoint temperature can also be selected by using the MODE touch button to browse to

the “

DHW setpoint temperature

" display option. When this option appears on the display, touch

the "+ /-" symbols to select the desired temperature.

If you wish to totally disable the boiler’s DHW production function, select the setpoint value "

OFF

by touching the "-" symbol until this value appears on the display. In this case DHW will only be

produced by the boiler’s solar heating system.

Summary of Contents for EVOLUTION SOLAR HFD

























































Search results

Summary of Contents for EVOLUTION SOLAR HFD

Reviews:

Related manuals for EVOLUTION SOLAR HFD

Brands by name

Popular brands

DOMUSA TEKNIK EVOLUTION SOLAR HFD, Installation And Operating Instructions Manual

Search results

Summary of Contents for EVOLUTION SOLAR HFD

Reviews:

Related manuals for EVOLUTION SOLAR HFD

Brands by name

Popular brands