![background image](http://html1.mh-extra.com/html/domo/do917gdk/do917gdk_instruction-booklet_2519939033.webp)
33
DO917GDK
www.domo-elektro.be
EN
· Allow the appliance to stand for 2 hours before turning it on. This allows the cooling agent
to settle.
· After installation, leave the freezer for 12 hours before turning it on. This way the
refrigerant can settle.
DOOR CONVERSION
The refrigerator has a reversible door. If you need to hinge your door on the opposite side it is
recommended that you call your local authorised service agent to make this conversion or ask
a technician.
Before you reverse the door, you should ensure the appliance is unplugged and empty.
Reversing the Door Swing of Your
Beverage Cooler
Before Reversing the door ,the power must be shut off.
All parts removed must be saved to do the reinstallation of the door.
NOTE:
This beverage c
ooler has the capability of either opening the door from the
left or right side. The unit is delivered to you with the door opening from the
left side. Should you desire to reverse the opening direction, please follow
these instructions.
This beverage c
ooler has been built with the door hinges on the left. If you wish
to change the opening direction, follow the instructions below:
2. Remove the two screws (1) that hold the upper hinge (5) (right side) to the
frame. Take away the upper hinge (5).
3. Lift the door and place it on a padded surface to prevent scratching it.
5. Remove the two screws(8) that hold the lower hinge(2) and Make sure to
Remove the lower hinge(2).
6. Remove the left front leg (4) and transfer it to the right side.
7. Remove the hole cover plate(7) to the right side.
8.
Before placing this lower hinge(2), remove the bolt-pin (9) and reverse
the direction of the lower hinge(2). Then install the lower hinge (2) onto
the left side of the lower frame with two screws (8).
10. Set the door to its place making sure the door seat at the lower hinge(2)
.
11. While holding the door in the closed position secure the upper hinge (5) in the
top frame of left side with two screws (1). Please remember that do not tighten
the two screws(1) until the top of the door is levelled with the counter top.
1. Remove the upper hinge cover(6) first
12. Install the upper hinge cover(6) on the upper hinge..
9. Insert the bolt-pin(9) to the lower hinge (2).
4. Remove the two screws (10) that hold the handle (11) (on the right side frame).
Change the handle to the left side frame.
4
8
3
7
2
9
1
6
5
8
3
9
2
4
7
1
6
5
Door opening from left side
Door opening from right side
10
11
11
10
Page 15 from 20
15
1. Remove the cover plate (6) of the hinges.
2. Remove the two screws (1) of the upper hinge (5). Remove the hinge.
3. Lift the door off and place it on a soft surface to prevent scratching.
4. Remove the screws (10) of the handle (11). Move the handle to the other side.
5. Remove the screws (8) and the hinge (2) to the other side of the door.
6. Remove the adjustable foot (4) and place it on the other side.
7. Move the cover plate of the drill holes (7) on the top of the refrigerator to the other side.
8. Before you replace the bottom hinge (2), remove the hinge pin (9) and reverse the
direction of the hinge. Replace the hinge (2) on the other side and fasten it with the two
screws (8).
9. Place the hinge pin (9) in the hinge (2).
10. Position the door on the lowest hinge (2).
11. Grip the door in a closed position and fasten the top hinge (5) with the two screws (1).
With the door closed, check whether the door is aligned horizontally as well as vertically
and that the seal closes on all sides before you tighten the upper hinge (5) completely.
12. Replace the cover plate (6). If necessary, adjust the adjustable feet.