manualshive.com logo in svg

Domnick Hunter Maxigas 104, Service Manual

Share
Download
Domnick Hunter Maxigas 104 Service Manual Download Page 28

 

 

 

28 

 

 

E8 - Diagnostics 

  
This feature is a view-only feature. No configuration changes are possible from within this menu. 
 
The display will alternate between the current value and diagnostic code 

E:8x

: where x is one of the following variables: 

 
0  Sensor signal, A to D counts low ppm range. 
1  Sensor signal, A to D counts high ppm range. 
2  Sensor signal, A to D counts %vol range. 
3 Firmware version. 
 
The diagnostic code can be selected by pressing the 

[   ]

 key. 

 
Press 

[ MENU ]

 to return the instrument to its standard mode of operation. 

 
 

 

E9 - Restore 

 
This option allows the user to restore the configuration data to the factory default values. The user can restore either or both 
sensor data. 
 

 

The analyser must be calibrated after a restore. All previous calibration data for 
the selected sensor will be lost. 

 
Press the 

[   ]

 key to select the sensor type. 

 
Press 

[ 

 ]

 to restore the selected sensor data. The display will show ‘

– – – –

‘ to confirm that the restore has been 

performed. 
 

Note: Pressing the [ MENU ] key rather than the 

[ 

 ]

 key exits the restore feature without performing any change. 

 
Press the 

[ MENU ]

 key to close the menu system. 

 

Note: The sensor zero factor will be displayed on exit while the 

[ MENU ]

 key is pressed. 

 

 

 
 
 

Summary of Contents for Maxigas 104





































Reviews:

No comments

Brands by name

Popular brands

Load more brands