Dometic AH-Passport I/O Compact Installation And Operation Manual Download Page 2

2

EN

Contents 

Passport I/O Digital Controls

Contents  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  . 2

1  Explanation of Symbols and Safety 

Instructions    .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  . 2

1.1 

Recognize Safety Information  . . . . . . . . . . . . . 2

1.2  Understand Signal Words . . . . . . . . . . . . . . . . 3
1.3  Supplemental Directives . . . . . . . . . . . . . . . . . 3
1.4  General Safety Messages  . . . . . . . . . . . . . . . . 3

2  Intended Use   .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  . 3

3  General Information   .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  . 4

3.1  Tools and Materials  . . . . . . . . . . . . . . . . . . . . . 4
3.2  Display Features   . . . . . . . . . . . . . . . . . . . . . . . 4

4 Specifications    .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  . 5

4.1  Product Dimensions   . . . . . . . . . . . . . . . . . . . . 5
4.2  Cable Length  . . . . . . . . . . . . . . . . . . . . . . . . . . 5
4.3  Available System Inputs . . . . . . . . . . . . . . . . . . 6
4.4  Operational Specifications  . . . . . . . . . . . . . . . 6

5  Wiring Diagrams   .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  . 7

6 Installation   .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  . 8

6.1  Choosing a Display Panel Location. . . . . . . . . 9
6.2  Preparing the Wall  . . . . . . . . . . . . . . . . . . . . . . 9

6.3  Installing an Optional Sensor   . . . . . . . . . . . . . 9
6.4  Mounting the Display Panel   . . . . . . . . . . . . . . 9

7 Operation  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  . 10

7.1 

Understanding the Heating and Cooling 
Cycles   . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10

7.2  Understanding the Service Utility  

Commands (DX Systems Only)  . . . . . . . . . . . 12

7.3  Turning on the Passport Control  . . . . . . . . . . 12
7.4  Choosing the Passport Control Operation  . 12
7.5  Using the Passport Control Display Panel   . . 14
7.3  Programming the Passport Control   . . . . . . . 16
7.4  Navigation Tree  . . . . . . . . . . . . . . . . . . . . . . .22

8 Maintenance    .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  . 23

8.1  Testing the Passport Control  . . . . . . . . . . . . .23
8.2  Checking the Return-Air Filter . . . . . . . . . . . .23
8.3  Energizing the Reversing Valve Units  

(DX Systems Only)  . . . . . . . . . . . . . . . . . . . . .23

8.4  Checking the Seawater Strainer  

(DX Systems Only)  . . . . . . . . . . . . . . . . . . . . .23

8.5  Cleaning the Condenser Coil  

(DX Systems Only)  . . . . . . . . . . . . . . . . . . . . .24

8.6  Winterizing the System (DX Systems Only) . .24

9 Troubleshooting    .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  . 25

10 Disposal   .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  . 29

11  Warranty Information  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  . 29

Service Center & Dealer Locations

Visit: www.dometic.com

Please read these instructions carefully and follow all instructions, 
guidelines, and warnings included in this product manual in order to 
ensure that you install, use, and maintain the product properly at all 
times. These instructions MUST stay with this product.

By using the product, you hereby confirm that you have read 
all instructions, guidelines, and warnings carefully and that you 
understand and agree to abide by the terms and conditions as set 
forth herein. You agree to use this product only for the intended 
purpose and application and in accordance with the instructions, 
guidelines, and warnings as set forth in this product manual as well 
as in accordance with all applicable laws and regulations. A failure 
to read and follow the instructions and warnings set forth herein may 
result in an injury to yourself and others, damage to your product, 
or damage to other property in the vicinity. This product manual, 
including the instructions, guidelines, and warnings, and related 
documentation, may be subject to changes and updates. For up-to-
date product information, please visit www.dometic.com.

Contents

1  Explanation of Symbols and 
Safety Instructions

This manual has safety information and instructions to 
help you eliminate or reduce the risk of accidents and 
injuries. 

1 .1  Recognize Safety Information

 

This is the safety alert symbol . 

It is used to alert 

you to potential physical injury hazards. Obey all 
safety messages that follow this symbol to avoid 
possible injury or death.

Summary of Contents for AH-Passport I/O Compact

































Reviews: