Dometic AH-Passport I/O Compact Installation And Operation Manual Download Page 3

3

EN

Passport I/O Digital Controls 

Intended Use

1 .2  Understand Signal Words

A signal word will identify safety messages and property 
damage messages, and also will indicate the degree or 
level of hazard seriousness.

 

DANGER!

Indicates a hazardous situation that, if 

not

 avoided, 

will result in death or serious injury.

 

WARNING

Indicates a hazardous situation that, if 

not

 avoided, 

could result in death or serious injury.

 

CAUTION

Indicates a hazardous situation that, if 

not

 avoided, 

could result in minor or moderate injury.

NOTICE: 

Used to address practices 

not

 related to 

physical injury.

 

I

Indicates additional information that is not related 
to physical injury.

1 .3  Supplemental Directives

To reduce the risk of accidents and injuries, please 
observe the following directives before proceeding to 
install or operate this appliance:

•  Read and follow all safety information and 

instructions.

•  Read and understand these instructions before 

installing and operating this product.

•  The installation must comply with all applicable local 

or national codes, including the latest edition of the 
following standards:

 

– ANSI/NFPA70, National Electrical Code (NEC)

 

– American Boat and Yacht Council (ABYC)

1 .4  General Safety Messages

 

WARNING: ELECTRICAL SHOCK, FIRE, AND/
OR EXPLOSION HAZARD . Failure to obey the 
following warnings could result in death or 
serious injury:

•  Use only Dometic replacement parts and 

components that are specifically approved for use 
with the appliance.

•  Avoid improper installation, adjustment, alteration, 

service, or maintenance of the appliance. Service 
and maintenance must be done by a qualified service 
person only.

•  Do 

not

 modify this product in any way. Modification 

can be extremely hazardous.

2  Intended Use

The Passport I/O controls and AH-Passport I/O 
controls (also referred to as “Passport controls”) are 5 V 
microcontroller-based devices designed for use with 
direct expansion (DX), reverse-cycle air-conditioning 
systems, and chilled-water systems (CW). 

The Passport controls are only suitable for the intended 
purpose and application in accordance with these 
instructions.

This manual provides information that is necessary 
for proper

 

installation and operation of the Passport 

controls. Poor installation and/or improper operating 
or maintenance will result in unsatisfactory performance 
and a possible failure. The manufacturer accepts no 
liability for any injury or damage to the product resulting 
from:

•  Incorrect assembly or connection, including excess 

voltage 

•  Incorrect maintenance or use of spare parts 

other than original spare parts provided by the 
manufacturer

•  Alterations to the product without express permission 

from the manufacturer

•  Use for purposes other than those described in this 

manual

Dometic reserves the right to change product 
appearance and product specifications.

Summary of Contents for AH-Passport I/O Compact

































Reviews: