manualshive.com logo in svg

Dometic 3311931.000-20, Installation Instructions Manual, Page: 14 / 17

Share
Download
Dometic 3311931.000-20 Installation Instructions Manual Download Page 14

14

a.  Re-connect the 12 Vdc and 120 Vac power 

supplies.

b.  Make sure the CCC 2 thermostat is in the 

OFF

 mode.

c.  Simultaneously press the 

MODE

 and 

Zone

 

buttons. The LCD will display "Init" and all 

available zones.

d.  Release the 

MODE

 and 

Zone

 buttons.

e.  Press the 

ON/OFF

 button to exit system set 

up.

f.  When a dip switch is turned on after initial 

configuration, a system reset will need to be 

done before the CCC 2 thermostat will rec-

ognize the updated selection.

2.  System Checkout

a.  Verify that all features of the installed sys-

tem work. See CCC 2 thermostat Operating 

Instructions or User's Guide. Check the fan  

mode, cooling mode, heating mode (if ap-

plicable), and furnace mode (if applicable) 

operation. If the features do not work discon-

nect the 120 Vac and 12 Vdc power supplies 

and verify that all wiring is correct and that 

the correct dip switches have been set to the 

"

ON

" position.

O.  (CCC 2 System Only) Furnace /Aqua 

Temperature Differential Setting

This system can be configured to operate using an ON/OFF 

differential of either 1 degree F or 2 degree F. See (FIG. 26).

1.  To set the differential, simultaneously press 

the 

PROGRAM

 button and the   up button 

on the CCC 2 thermostat. "diF1" will appear in 

the display while the buttons are pressed. See 

(FIG. 26). To set the 2 degree differential, simul-

taneously press the 

PROGRAM

 button and the 

 down button. "diF2" will appear in the display 

while the buttons are pressed.

FIG. 26

h.  Gen Start selection - Leave in the "OFF" po-

sition.

i.  Install electronic control box cover.
j.  Repeat this procedure for each additional 

zone.

FIG. 24

On Position

Off Position

M.  Installing Return Air Cover

1.  

Remove the return air grille from the return air 

cover.

2.  Place the return air cover up to the ceiling tem-

plate.

3.  Install cover to template using six (6) supplied 

#8 x 3/8″ blunt point Phillips head screws.

4. 

Reinstall filter return air grille into return air cov

-

er. Align tabs with mating notches and snap into 

place.

5.  Install two (2) hole plugs into screw holes in 

back of return air cover. See (FIG. 25).

FIG. 25

Hole Plug

Return Air 

Grille

Return Air 

Cover

N.  (CCC 2 System Only) Reset & Checkout

1.  System Reset

After setting the dip switches in the electronic 

control, do a system reset.

INSTALLATION INSTRUCTONS

Summary of Contents for 3311931.000-20


















Reviews:

No comments