background image

 

domat UC300 

01/2019 Subject to technical changes. 

Change of setpoints and controller time: 

 
Switch to the settings mode with a super long push (>2.5 s). The controller switches to 
settings mode (flashing thermometer icon). 
 
Turning the knob selects between following settings: 

-

 

Controller time and day of week (Clock icon, Day of week) 

-

 

Setpoint temp. Heating Day mode (Temperature, Heating, Day are flashing) 

-

 

Setpoint temp. Heating Night mode (Temperature, Heating, Night are flashing) 

-

 

Setpoint  temp.  Heating  Off  mode  (Temperature,  Heating,  Empty  house  are 
flashing) 

-

 

Setpoint temp. Cooling Day mode (Temperature, Cooling, Day are flashing) 

-

 

Setpoint temp. Cooling Night mode (Temperature, Cooling, Night are flashing) 

-

 

Setpoint  temp.  Cooling  Off  mode  (Temperature,  Cooling,  Empty  house  are 
flashing) 

 
Select the requested value by a short push. Turn knob to change value. Confirm by a 
short push again.  
 
If there is no user activity for 30 s, the controller goes to the basic display mode. 
 

Default values: 

 
Default values as well as all other settings (PI parameters, address, baud rate...) can be 
set  by  the  configuration  program,  ModComTool,  and  a  USB/RS485  or  RS232/RS485 
converter 

 see Related products. 

 

Display 
 
 

 

 

 

A large (60 x 60 mm) display clearly shows 
actual  room  temperature  and  controller 
status with 7-segment digits and standard 
Day,  Night,  Off,  and  Time  scheduler 
symbols.  Active  output  is  indicated  by  a 
heating  symbol. In  the  upper  part,  there 
are  week  days  used  for  time  scheduler 
setup. Other symbols are not used. 
 
 
 
LCD symbol set 
 

Summary of Contents for UC300









Reviews: