background image

 

domat UC010 

08/2018 Subject to technical changes. 

5

 

Short push to confirm the operation mode setting. The event time displays. Turn the 
knob to set the time of the event and confirm by a short push. Then turn the knob to 
select another event or long push and turn the knob to select another weekday. 
 
After all desired events have been edited, long push to leave the time schedule settings. 
The controller goes to the basic display mode also after 30 secs of user inactivity. 
 

Change of setpoints and controller time: 

 
Switch to the settings mode with a superlong push (>2.5 s). The controller switches to 
settings mode (flashing thermometer icon). 
 

Turning the knob selects between following settings: 
 

-

 

Controller time and day of week (Clock icon, Day of week) 

-

 

Setpoint temp. Heating Day mode (Temperature, Heating, Day are flashing) 

-

 

Setpoint temp. Heating Night mode (Temperature, Heating, Night are flashing) 

-

 

Setpoint  temp.  Heating  Off  mode  (Temperature,  Heating,  Empty  house  are 
flashing) 

-

 

Setpoint temp. Cooling Day mode (Temperature, Cooling, Day are flashing) 

-

 

Setpoint temp. Cooling Night mode (Temperature, Cooling, Night are flashing) 

-

 

Setpoint  temp.  Cooling  Off  mode  (Temperature,  Cooling,  Empty  house  are 
flashing) 

 
Select the requested value by a short push. Turn knob to change value. Confirm by a 
short push again.  
 
If there is no user activity for 30 s, the controller goes to the basic display mode. 
 

Default values: 

 
The default values as well as all other settings (PI parameters, address, baudrate...) can 
be set by the configuration program, ModComTool.  

Display 

 

A  large  (60  x  60  mm)  display  clearly  shows 
actual room temperature and controller status 
with 7-segment digits and standard Day, Night, 
Off, and Time scheduler symbols. Active output 
is indicated by a heating symbol. In the upper 
part,  there  are  week  days  used  for  time 
scheduler setup. Other symbols are not used. 
 
 
 
LCD symbol set 
 

 

 

Summary of Contents for UC010








Reviews: