manualshive.com logo in svg

Dolphin Blue 620, Installation And Maintenance Manual, Page: 8 / 15

Share
Download
Dolphin Blue 620 Installation And Maintenance Manual Download Page 8

8 

|  

Dolphin

| 

DB620 / DB 625

INSTLLATION PROX FRONT FIXATION

5. If your system is provided with an inlet

nipple fit the water supply inlet to the

inlet nipple at the solenoid valve housing

or connect it directly to the shut off valve.

6. Turn on the central water supply and

the shut-off valves (angle valves) and

check for leaks.

7. Connect the waterproof connector

coming from the prox sensor to the

solenoid valve connector.

Step 3– Connecting the power source

1. Connect the waterproof connector

coming from the prox sensor to the 

power source.

2. For battery models: Install the battery

box at the wall using the screws or the

two sided adhesive foam tape.

3. For transformer models: a. Connect the

waterproof connector coming from the

prox sensor to the transformer. b. Plug the

transformer into the electrical socket.

Important: In order to avoid going into adjusting mode, wait 10 seconds before
operating the system.

Summary of Contents for Blue 620
















Reviews:

No comments