manualshive.com logo in svg

Dolmar PS-6400, Repair Manual

Share
Download
Dolmar PS-6400 Repair Manual Download Page 38

38

Repair Manual PS-6400/PS-7300/PS-7900

1

(10,0 Nm  ± 1,0)

2

3

4

4

5

5

(10.0 Nm ± 1.0)

1 2

OUTSIDE COMPONENTS / CRANKCASE / CRANKSHAFT

Crankcase

The clutch-side and magneto-side crankcase halves
can be individually replaced.
They are bolted together with 6 Torx screws 

1

(M5 x 30).
Pinned distortion-free with 2 spiral spring pins 

2

(3 x 16 mm).
Always apply a dry new gasket 

3

 (038.111.042).

Cut off the excess gasket after crankcase assembly
is complete.

Replacing the radial ring

A new radial ring puller is in progress.
Fill new radial ring 

5

 with grease and insert in

crankcase with the special tool.

Replacing the crankshaft

Heat the crankcase clutch-side and magneto-side
to 150-160°C (302-320°F).
Evenly coat the external ring of the ball bearing 

4

with “Loctite 601” and insert into the heated
crankcase without pressure.
Lubricate the big end bearing 

5

 with two-stroke oil.

Tool

Summary of Contents for PS-6400













































Reviews:

No comments

Brands by name

Popular brands

Load more brands