15 ENGLISH
Battery remaining capacity indicator
(only for models with Battery
AP-3622/ BL3622A)
Battery AP-3622/ BL3622A are equipped with the bat-
tery remaining capacity indicator.
►
Fig.7:
1.
Indicator lamps
2.
CHECK button
Press the CHECK button to indicate the battery remain-
ing capacity. The indicator lamps will then light for
approx. three seconds.
Indicator lamps
Lighted Off
Blinking
E
F
Remaining capacity
70% to 100%
45% to 70%
20% to 45%
0% to 20%
Charge the battery.
The battery may have
malfunctioned.
•
When only the lowermost indicator lamp (next
to the “E”) blinks, or when none of the indicator
lamps light, the battery capacity has run out, so
the tool does not operate. In these cases, charge
the battery or replace the empty battery with a fully
charged one.
•
When two or more indicator lamps do not light
even after charging is complete, the battery has
reached the end of its service life.
•
When the upper two and lower two indicator
lamps light alternately, the battery may have mal-
functioned. Contact your local Dolmar authorized
service center.
NOTE:
•
The indicated capacity may be lower than the
actual level during use or immediately after
using the tool.
•
Depending on the conditions of use and the
ambient temperature, the indication may differ
slightly from the actual capacity.
ASSEMBLY
CAUTION:
•
Always be sure that the tool is switched off and
the battery cartridge is removed before carrying
out any work on the tool.
Installing or removing saw chain
CAUTION:
•
Always be sure that the tool is switched off and
the battery cartridge is removed before installing
or removing the saw chain.
•
Always wear gloves when installing or removing
the saw chain.
1.
To remove the saw chain, slightly slide the lever
in the direction of arrow so that it can be released
from the locked position and move the lever in the
upright position as shown in the figure.
►
Fig.8:
1.
Slightly slide
2.
Move in the upright position
►
Fig.9:
1.
Press in
2.
Loosen
3.
Sprocket cover
4.
Adjusting dial
2.
Press the lever and with the lever pressed in, turn
it counterclockwise to loosen the nut until sprocket
cover comes off. (Pressing in the lever leads to the
fitting of lever into the nut.)
3. Turn the adjusting dial counterclockwise to release
the saw chain tension.
4.
Remove the sprocket cover.
5. Remove the saw chain and guide bar from the chain saw.
6. To install the saw chain, fit in one end of the saw
chain on the top of the guide bar and the other end
of it around the sprocket.
►
Fig.10:
1.
Sprocket
At this time, fit the saw chain as shown in the figure
because it rotates in the direction of arrow.
7.
Rest the guide bar in place on the chain saw
8. Turn the adjusting dial counterclockwise to slide
the adjusting pin in the direction of arrow.
►
Fig.11:
1.
Adjusting pin
9.
Place the sprocket cover on the chain saw so that
the adjusting pin is positioned in a small hole in
the guide bar.
►
Fig.12:
1.
Small hole
10. Press in the lever and with the lever depressed
turn it fully clockwise to tighten the nut. Then make
it about a quarter turn counterclockwise to loosen
the nut lightly.
►
Fig.13:
1.
Press in
2.
Tighten
3.
Loosen
Adjusting saw chain tension
►
Fig.14:
1.
Lever
The saw chain may become loose after many hours of use.
From time to time check the saw chain tension before use.
Move the lever in the upright position.
►
Fig.15:
1.
Press in
2.
Loosen
Press in the lever. With the lever depressed, make a quarter
turn on it counterclockwise to loosen the nut lightly. (Pressing
in the lever leads to the fitting of lever into the nut.)
►
Fig.16:
1.
Low
2.
High
3.
Adjusting dial
4.
Guide bar
5.
Saw chain
Turn the adjusting dial to adjust saw chain tension. Grasp
the saw chain in the middle of the guide bar and lift up. The
gap between the guide bar and the tie strap of the saw chain
should be approx. 2 - 4 mm. If the gap is not approx. 2 - 4 mm,
slightly turn the adjusting dial which secures the guide bar. At
this time, adjust with the tip of guide bar slightly pointing up.
Summary of Contents for AS-3625
