Dodge 2016 Viper SRT ACR Owner'S Manual Download Page 153 | Manualshive

Page: 153 / 427

background image

Air Bag Warning Light

Red Telltale

Light

What It Means

Air Bag Warning Light

This light will turn on for four to eight seconds as a bulb check when the ignition switch is
first turned to ON/RUN. If the light is either not on during startup, stays on, or turns on
while driving, have the system inspected at an authorized dealer as soon as possible. This
light will illuminate with a single chime when a fault with the Air Bag Warning Light has
been detected, it will stay on until the fault is cleared. If the light comes on intermittently or
remains on while driving, have an authorized dealer service the vehicle immediately. Refer
to “Occupant Restraints” in “Things To Know Before Starting Your Vehicle” for further infor-
mation.

4

UNDERSTANDING YOUR INSTRUMENT PANEL

151

«
...
151
152
153
154
155
...
»

Summary of Contents for 2016 Viper SRT ACR












































































































































































































































































































































































































































Reviews:

No comments

Related manuals for 2016 Viper SRT ACR

Brand: cam Pages: 2

Brand: Dapper Lighting Pages: 2

Brand: Prorack Pages: 14

Brand: UAZ Pages: 90

Brand: AddSecure Pages: 14

Brand: Fiat Pages: 24

Brand: Valeo Pages: 28

Brand: Baja Designs Pages: 5

Brand: Yakima Pages: 9

Crossland X 2017

Brand: Vauxhall Pages: 245

nERGY ETSA200R-PA

Brand: Soundoff Signal Pages: 3

Brand: Truma Pages: 10

Brand: Volkswagen Pages: 68

Brand: Easee Pages: 21

Brand: ULTIMATE SPEED Pages: 132

Brand: Menabo Pages: 4

1967 Calais Coupe

Brand: Cadillac Pages: 255

Brand: Subaru Pages: 9

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands