Dodge 2016 Viper SRT ACR Owner'S Manual Download Page 14 | Manualshive

Page: 14 / 427

background image

Key Fob

The Key Fob also contains the Remote Keyless Entry
(RKE) transmitter and an emergency key, which stores in
the rear of the Key Fob.

The emergency key allows for entry into the vehicle
should the battery in the vehicle or the Key Fob go dead.
You can keep the emergency key with you when valet
parking.

To remove the emergency key, slide the mechanical latch
on the back of the Key Fob sideways with your thumb
and then pull the key out with your other hand.

NOTE:

In the event that the FOB does not start the

vehicle (

⬙

FOB not Found

⬙

message) use the FOB nose

(furthest point from key ring) and push the start button.
FOB replaces the finger.

— RKE Liftgate Button

— RKE Door Unlock Button

— RKE Door Lock Button

— RKE PANIC Alarm Button

Remote Keyless Entry (RKE) Transmitter

12

THINGS TO KNOW BEFORE STARTING YOUR VEHICLE

«
...
12
13
14
15
16
...
»

Summary of Contents for 2016 Viper SRT ACR












































































































































































































































































































































































































































Reviews:

No comments

Related manuals for 2016 Viper SRT ACR

Brand: AA Products Pages: 4

Brand: Kuda Pages: 3

Brand: Draw tite Pages: 4

Brand: Mercedes-Benz Pages: 329

Brand: mtf TRANSPORT SYSTEM Pages: 9

Brand: Volvo Pages: 42

Brand: Saab Pages: 15

2000 9-5 2.3 Turbo Ecopower

Brand: Saab Pages: 256

Brand: Prime Design Pages: 8

Telescoping Computer Base C-TCB-34

Brand: Havis-Shields Pages: 1

Brand: PEUGEOT Pages: 107

Brand: Volvo Pages: 18

Brand: ideus Pages: 116

Brand: LaserLine Pages: 4

PRIME DESIGN UXV 211

Brand: Safe Fleet Pages: 8

Brand: 3SIXT Pages: 4

Follow me RAPID INTRACKER

Brand: Thule Pages: 8

Tri-Mount 34269

Brand: PowerMadd Pages: 2

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands