Dodge 2011 Grand Caravan Owner'S Manual Download Page 237 | Manualshive

Page: 237 / 562

background image

NOTE:

•

Crossbars are error-proofed and cannot be deployed or
stowed in the incorrect positions.

•

To help control wind noise, stow the crossbars in the
side rails when they are not in use.

Deploying the Crossbars

To deploy the crossbars, completely loosen the thumb
screws at both ends of the crossbar and lift the crossbar
from its stowed position in the side rail. Repeat with
crossbar on the opposite side.

CAUTION!

Use care when removing and handling the crossbars
to prevent damage to the vehicle.

Loosening Crossbars

3

UNDERSTANDING THE FEATURES OF YOUR VEHICLE

235

«
...
235
236
237
238
239
...
»

Summary of Contents for 2011 Grand Caravan



















































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for 2011 Grand Caravan

Brand: Ranger design Pages: 6

Brand: Edelbrock Pages: 1

Brand: FORM FIT Pages: 2

Brand: Dacia Pages: 238

Sedan CIVIC 2022

Brand: Honda Pages: 701

Brand: Jaeger Pages: 11

ESCALADE ESV 2005

Brand: Cadillac Pages: 482

Brand: curt Pages: 4

Brand: Fabbri Pages: 32

Brand: Whelen Engineering Company Pages: 2

Brand: FIRRAK Pages: 12

Brand: Volvo Pages: 5

Brand: Erich Jaeger Pages: 16

Brand: Navman Pages: 10

BUSHMAN 15L ROADIE fridge Base console

Brand: Cruiser Consoles Pages: 6

Brand: Road Ranger Pages: 3

Brand: Ford Pages: 17

AC-12PROWLER-FC04

Brand: FALCON RIDGE Pages: 9

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands