manualshive.com logo in svg

Dodge 2011 Challenger, Owner'S Manual

The Dodge 2011 Challenger is a powerhouse of a vehicle, providing an exhilarating driving experience. To ensure you get the most out of your Challenger, make sure to download the free user manual from manualshive.com. This manual offers detailed specifications and instructions to help you fully enjoy this iconic car.

Share
Download
background image

WARNING!

Overloading of your tires is dangerous. Overloading
can cause tire failure, affect vehicle handling, and
increase your stopping distance. Use tires of the
recommended load capacity for your vehicle. Never
overload them.

TIRES — GENERAL INFORMATION

Tire Pressure

Proper tire inflation pressure is essential to the safe and
satisfactory operation of your vehicle. Three primary
areas are affected by improper tire pressure:

Safety

WARNING!

•

Improperly inflated tires are dangerous and can
cause collisions.

•

Under-inflation increases tire flexing and can re-
sult in over-heating and tire failure.

•

Over-inflation reduces a tire’s ability to cushion
shock. Objects on the road and chuckholes can
cause damage that result in tire failure.

•

Unequal tire pressures can cause steering prob-
lems. You could lose control of your vehicle.

•

Over-inflated or under-inflated tires can affect
vehicle handling and can fail suddenly, resulting
in loss of vehicle control.

(Continued)

300

STARTING AND OPERATING

Summary of Contents for 2011 Challenger











































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for 2011 Challenger

Qube AP1 Supplemental Instructions preview
AP1
Brand: Qube Pages: 19
Cadillac 2000 Warranty And Owner Assistance Information preview
2000
Brand: Cadillac Pages: 32
Eaton Green Motion DC 22 Training preview
Green Motion DC 22
Brand: Eaton Pages: 65
Falcon 1990 Installation Instructions And Specifications preview
1990
Brand: Falcon Pages: 8
SAF-HOLLAND FleetMaster Air FW8 Series Owner'S Manual preview
FleetMaster Air FW8 Series
Brand: SAF-HOLLAND Pages: 20
TATA Motors nano genX Owner'S Manual preview
nano genX
Brand: TATA Motors Pages: 156
Fiat 500 L 2019 User Manual preview
500 L 2019
Brand: Fiat Pages: 172
Honda HondaLink Quick Start Manual preview
HondaLink
Brand: Honda Pages: 6
Kia Sportage 2018 Features & Functions Manual preview
Sportage 2018
Brand: Kia Pages: 54
STO N SHO SNS135a Installation Procedures Manual preview
SNS135a
Brand: STO N SHO Pages: 7
Chevrolet Impala Limited 2014 Owner'S Manual preview
Impala Limited 2014
Brand: Chevrolet Pages: 356
Unex OBU-352EC Quick Start Manual preview
OBU-352EC
Brand: Unex Pages: 30
Prime Design URX-001-E Assembly Instructions Manual preview
URX-001-E
Brand: Prime Design Pages: 8
MayPole BC2085 Manual preview
BC2085
Brand: MayPole Pages: 3
Nos 05183NOS Owner'S Manual preview
05183NOS
Brand: Nos Pages: 22
Yakima TopWater Quick Start Manual preview
TopWater
Brand: Yakima Pages: 9
Spracht Aura Mobile BT MCP-2014 Quick Start Manual preview
Aura Mobile BT MCP-2014
Brand: Spracht Pages: 2
Cadillac CTS 2011 Manual preview
CTS 2011
Brand: Cadillac Pages: 78

Brands by name

Popular brands

Load more brands