background image

The ACTIVE-Button

The ACTIVE-Button

The ACTIVE-Button

The ACTIVE-Button

IMC5 has a "true bypass" circuit. This circuit makes it possible for the 
device to remain in the signal path even without a power supply. In this
case, the applied audio signal is switched to the output directly and 
lossless. 
The ACTIVE button on the front left of the front panel allows manual 
switching of true bypass. A red LED is signalizing an active unit.

The EQ-Button

The EQ-Button

The EQ-Button

The EQ-Button

The knob in the middle switches the EQ in the audio-path. A pressed 
switch causes a red LED to light up and is signalizing an active EQ. 
Use this switch for a quick check of the defeat signal against the EQ 
signal.

The FF/FB-Button / OVER-LED

The FF/FB-Button / OVER-LED

The FF/FB-Button / OVER-LED

The FF/FB-Button / OVER-LED

This knob defines the working character of the compressor.
There are two types of signal tap for the sidechain: The feed forward 
(= FF) is the signal before the compressor tapped, with feed backward
(= FB) after the compressor.
Newer compressors work almost exclusively with "Feed Forward" (FF). 
Many "classics" (such as 1176 or 660) used the Feed Backward (FB) 
method. The difference between the types: FF intervenes much "harder"
in the signal. FB allows a much "gentler" method of compression.
If the knob is pressed the compressor is working in FF-mode. A 
unpressed knob means that the compressor is working in FB-mode. 

The LED inside the switch is a signal overload indicator (OVER). It flashes in case of an output signal 
greater than +6 dB. It's not a signal indicating distortion! It just informs the user that you are 
reaching a zone in which you have to be careful not to jump over the top. 
The FF/FB-button has no illumination itself.

INPUT

INPUT

INPUT

INPUT

The INPUT potentiometer is an attenuation of the input signal. It reduces the 
input signal in a range from -10 dB to 0 dB.   
Because IMC is a grateful amplifier it needs some “headroom” to work. Also 
one can reduce the pending signal before reaching the EQ.

IMC5

7

© DOCtron 2021

Summary of Contents for IMC5












Reviews: