Dobot Magician Lite User Manual Download

Page: 51 / 72

Dobot Magician Lite User Guide

Operation

Issue V1.9.1 (2020-01-11)

User Guide

Set the percentage of speed for playback, such as 50.

Set

Loop

Click

Start

. Magician Lite performs the sequence of ARC trajectory as taught from

its memory system, moving from positions A through C, as shown in Figure 5.22.

Figure 5.22 Move the small cube in the ARC motion mode

Teaching & Playback Example

Application Scenarios

You can use the Teaching & Playback function module to manipulate Magician Lite to

accomplish different tasks such as transportation or intelligent sort. This topic introduces how to

move small cubes from position A to B in the

JUMP

motion mode.

Prerequisites



Magician Lite has been powered on and connected to your computer.



A suction cup kit has been installed. For details, see

5.3.1 Installing a Suction Cup Kit

Procedure

Summary of Contents for Magician Lite









































































Search results

Summary of Contents for Magician Lite

Reviews:

Related manuals for Magician Lite

Brands by name

Popular brands

Dobot Magician Lite, User Manual

Search results

Summary of Contents for Magician Lite

Reviews:

Related manuals for Magician Lite

Brands by name

Popular brands