Dobot Magician Lite User Manual Download

Page: 42 / 72

Dobot Magician Lite User Guide

Operation

Issue V1.9.1 (2020-01-11)

User Guide

Prerequisites



Magician Lite has been powered on.



Magician Lite has been connected to DobotStudio successfully.

Procedure

Click

Home

on the DobotStudio page, as shown in Figure 5.6.

NOTICE



Please remove the end-effector from Magician Lite before homing.



Please ensure that there are no obstacles in the workspace during homing.

Figure 5.6 Operate homing

Magician Lite will rotate to the default homing point automatically and the LED indicator on

the base turns blue and is blinking. After the homing is successful, there is a beep sound and the

LED indicator turns green.

Also, the homing point can be user-defined, you can select a saved point on the

Teachong&Playback

page and right-click

SetHome

to set this saved point as the homing point, as

shown in Figure 5.7.

Figure 5.7 Set homing point

Performing Teaching & Playback Tasks

This topic introduces how to perform a teaching & playback task to suck or grab a small cube.

Because a suction cup kit or a gripper kit is required, we will explain them first.

Installing a Suction Cup Kit

Magician Lite has built-in air pump with suction cup as the default end-effector, as shown in

Summary of Contents for Magician Lite









































































Search results

Summary of Contents for Magician Lite

Reviews:

Related manuals for Magician Lite

Brands by name

Popular brands

Dobot Magician Lite, User Manual

Search results

Summary of Contents for Magician Lite

Reviews:

Related manuals for Magician Lite

Brands by name

Popular brands