background image

 

DER-S0080A 

Rev. 12©1999 - 2011 DMC Co., Ltd. 

ATP/AST Series Product Specifications

1. Product Specifications 

1-1. Product Applicable 

§ This specification is applied to the analog resistive touchscreen: ATP/AST Series.

 

 

1-2. Structure 

§ Dimensions, structure, and shape are referred on the drawing attached. 
 

1-3. Environmental Specifications 

Specification Value 

Operating Temperature 

-20°C to 70°C (no condensation) 

Operating Humidity 

-20°C to 60°C Less than 90%RH (no condensation) 

Exceeding 60°C 133.8g/m

3

 (no condensation) 

Storage Temperature 

-40°C to 80°C (no condensation) 

Storage Humidity 

-40°C to 60°C Less than 95%RH (no condensation) 

Exceeding 60°C 142.9g/m

3

 (no condensation) 

Chemical Resistance 

(top surface) 

Toluene, Tricholoroethylene, Athetone, Alcohol, 

Gasoline, Machine Oil, Ammonia, Glass Cleaner, 

  Mayonnaise, Ketchup, Wine, Salad Oil, Vinegar, Lipstick, etc. 

 

1-4. Mechanical Characteristics 

Specification Value 

Activation Force 

0.05N to 0.8N 

Input (finger) 

10,000,000 hits 

Operating Life 

Character Input (pen) 

100,000 characters 

Light Transmittance 

Over 80% (typical value at full wavelength) 

Surface Hardness 

Over 2H (by JIS pencil hardness) 

 

1-5. Electrical Characteristics 

Specification Value 

Maximum Voltage 

DC6V 

Top Electrode 

100mA 

Bottom Electrode 

100mA 

Maximum Current 

Between the Top and Bottom

0.5mA 

Linearity 

 Under 

±

2

% (

Under 

±

1% (typical value)) 

Top Electrode 

Less than 1k

Ω

 

Terminal Resistance 

Bottom Electrode 

Less than 1k

Ω

 

Neighboring Terminals 

Over 20M

Ω

 at 25V 

Insulation Resistance 

Active Area Electrodes 

Over 20M

Ω

 at 25V 

Chattering 

Less than 10msec at ON/OFF. 

Summary of Contents for Analog Resistive Touchscreen ATP/AST Series














Reviews:

Related manuals for Analog Resistive Touchscreen ATP/AST Series